Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 188

Страница: 188 / 1153

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

6-13

LLRS

Loss-of-lock reset status.
0

The last reset source acknowledged by the reset controller was not a loss-of-PLL lock reset.

The last reset source acknowledged by the reset controller was a loss-of-PLL lock reset.

LCRS

Loss-of-clock reset status.
0

The last reset source acknowledged by the reset controller was not a loss-of-clock reset.

The last reset source acknowledged by the reset controller was a loss-of-clock reset.

WDRS

Watchdog timer/debug reset status.
0

The last reset source acknowledged by the reset controller was not a watchdog timer or debug reset.

The last reset source acknowledged by the reset controller was a watchdog timer or debug reset.

CRS

Checkstop reset status.
0

The last reset source acknowledged by the reset controller was not an enabled checkstop reset.

The last reset source acknowledged by the reset controller was an enabled checkstop reset.

6–13

Reserved

SSRS

Software system reset status.
0

The last reset source acknowledged by the reset controller was not a software system reset.

The last reset source acknowledged by the reset controller was a software system reset.

SERF

Software external reset flag.
0

The software external reset input to the reset controller was not asserted, or this bit has been cleared by writing

a 1 to it.

The software external reset input to the reset controller was asserted while this bit was 0.

WKPCFG

Weak pull configuration pin status
0

The WKPCFG pin value latched during the last reset was a logical 0 and weak pulldown is the default setting.

The WKPCFG pin value latched during the last reset was a logical 1 and weak pullup is the default setting.

17–28

Reserved

Table 6-8. SIU_RSR Field Descriptions (continued)

Field

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды