Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 1153

background image

Reset

MPC5565 Microcontroller Reference Manual, Rev. 1.0

4-8

Freescale Semiconductor

and the associated bits/fields are updated in the SIU_RSR (the BOOTCFG[0:1] pins are only sampled if
RSTCFG asserts). In addition, the PORS and ERS bits are set, and all other reset status bits are cleared in
the reset status register.

Refer to

Section 4.2.2, “Reset Output (RSTOUT)

4.4.2.3.2

External Reset

When the reset controller detects assertion of the RESET pin, the internal reset signal and the RSTOUT
signal are asserted.

1. Starting when the internal reset signal asserts, as indicated by RSTOUT asserting, the value on the

WKPCFG pin is applied. At the same time, the PLLCFG[0:1] values are applied only if RSTCFG
asserts.

2. After the RESET signal negates and the FMPLL loss-of-lock request negates, the reset controller

waits the predetermined number of clock cycles. After the clock count finishes, WKPCFG and
BOOTCFG[0:1] are sampled. BOOTCFG[0:1] is only sampled if RSTCFG asserts.

3. The reset controller then waits four clock cycles before the negating RSTOUT, and updating the

fields in the SIU_RSR. The ERS bit is set, and all other reset status bits in the SIU_RSR are cleared.

Refer to

Section 4.2.2, “Reset Output (RSTOUT)

4.4.2.3.3

Loss-of-Lock Reset

A loss-of-lock reset occurs when the FMPLL loses lock and the loss-of-lock reset enable (LOLRE) bit in
the FMPLL synthesizer control register (FMPLL_SYNCR) is set.

1. Starting when the internal reset signal asserts, as indicated by RSTOUT asserting, the value on the

WKPCFG pin is applied. At the same time, the PLLCFG[0:1] values are applied only if RSTCFG
asserts.

2. After the FMPLL locks, the reset controller waits the predetermined clock count and then samples

WKPCFG and BOOTCFG[0:1]. BOOTCFG[0:1] is only sampled if RSTCFG asserts.

3. The reset controller then waits four clock cycles before negating RSTOUT and updating the

register fields in the SIU_RSR. The LLRS bit is set, and all other reset status bits in the SIU_RSR
are cleared.

Refer to

Section 4.2.2, “Reset Output (RSTOUT)

Refer to

Chapter 11, “Frequency Modulated Phase Locked Loop and System Clocks (FMPLL)

,”

for more information on loss-of-lock.

«
...
147
148
149
150
151
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Eaton Страницы: 166

Бренд: Samsung Страницы: 27

Бренд: Xilinx Страницы: 52

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: Cooper Страницы: 4

Бренд: Wavelength Electronics Страницы: 17

Бренд: Digiplex Страницы: 48

Бренд: Instrutech Страницы: 42

Бренд: Autoscript Страницы: 22

AK-CC 750 series

Бренд: Danfoss Страницы: 96

Бренд: Kamado Joe Страницы: 2

Бренд: VelLight Страницы: 44

Бренд: ECO POWER Страницы: 2

Бренд: Samson Страницы: 22

Бренд: Arduino Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды