Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 498 | Manualshive

Страница: 498 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

12-53

Signals Protocol

”) and the DATA bus, which are driven by the EBI for external master reads to internal

address space. As long as the external master device follows the same protocol for driving signals as this
EBI, there is no need to use the open drain mode of the pads configuration module for any EBI pins.

The Power Architecture storage reservation protocol is not supported by the EBI. Coherency between
multiple masters must be maintained via software techniques, such as event passing.

The EBI does not provide memory controller services to an external master that accesses shared external
memories. Each master must properly configure its own memory controller and drive its own chip selects
when sharing a memory between two masters.

The EBI does not support burst accesses from an external master; only single accesses of 8, 16, or 32 bits
can be performed.

1

12.4.2.10.1

Address Decoding for External Master Accesses

The EBI allows external masters to access internal address space when the EBI is configured for external
master mode. The external address is compared for any external master access, to determine if EBI
operation is required. Because only 24 address bits are available on the external bus, special decoding logic
is required to allow an external master to access on-chip locations whose upper 8 address bits are non-zero.
This is done by using the upper 4 external address bits (ADDR[8:11]) as a code to determine whether the
access is on-chip and if so, for which internal slave it is targeted.

NOTE

(External master accesses are not supported to the Calibration bus.)

The options for the address compare sequence are explained in the following bullets:

•

External master access to another device — If ADDR[8] = 0, then the access is assumed to be to
another device and is ignored by the EBI.

•

External master access to valid internal slave — If ADDR[8] = 1, then ADDR[9:11] are checked
versus a list of 3-bit codes to determine which internal slave to forward the access to. The upper 8
internal address bits are set appropriately by the EBI according to this 3-bit code, and internal
address bits [8:11] are set appropriately to match the internal slave selected.

•

External master access to invalid internal slave — If the 3-bit code does not match a valid internal
slave, then the EBI responds with a bus error.

1. Except for the special case of a 32-bit non-chip select access in 16-bit data bus mode. Refer to

Section 12.4.2.11,

“Non-Chip-Select Burst in 16-bit Data Bus Mode

”.

«
...
496
497
498
499
500
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: eclisse Страницы: 40

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: PENGWYN Страницы: 32

Бренд: Warner Electric Страницы: 6

Бренд: TSM Страницы: 2

RSF-B mini Series

Бренд: Harmonic Drive Страницы: 32

Бренд: Parker Страницы: 24

Бренд: Cruisair Страницы: 30

Бренд: Linear Technology Страницы: 6

ServeRAID M1215 SAS

Бренд: IBM Страницы: 35

Бренд: PacComm Страницы: 29

AK-CC 750 series

Бренд: Danfoss Страницы: 96

Бренд: Xilinx Страницы: 30

Бренд: SSK Страницы: 8

Бренд: Comunello Страницы: 112

exta life ROB-21

Бренд: Zamel Страницы: 24

SECURBASE LIGHT PLUS

Бренд: BFT Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды