Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 751 | Manualshive

Страница: 751 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-52

Freescale Semiconductor

Read Configuration Command Message Format for On-Chip ADC Operation

describes the command message format for a read configuration command when interfacing

with the on-chip ADCs. A read configuration command is used to read the contents of the on-chip ADC
registers which are only accessible via command messages. Read configuration commands are
differentiated from write configuration commands by an asserted R/W bit.

5

EB

External buffer bit. This bit should always be cleared for messages sent to an on-chip ADC.
0 Command is sent to an internal command buffer.
1 Command is sent to an external command buffer.

6

BN

Buffer number. Indicates in which buffer the message is stored. Buffers 1 and 0 can either be internal or external
depending on the EB bit setting.
0 Message stored in buffer 0.
1 Message stored in buffer 1.

7

R/W

Read/write. A negated R/W indicates a write configuration command.
0 Write
1 Read

8–15

ADC_

REGISTER

_HIGH_

BYTE[0:7]

ADC register high byte. The value to be written into the most significant 8 bits of control/configuration register
when the R/W bit is negated.

16–23

ADC_

REGISTER

_LOW_

BYTE[0:7]

ADC register low byte. The value to be written into the least significant 8 bits of a control/configuration register
when the R/W bit is negated.

24–31

ADC_REG_

ADDRESS

[0:7]

ADC register address. Selects a register on the ADC register set to be written or read. Only halfword addresses
can be used. Refer to

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

EOQ

PAUSE

Reserved

EB

(0b0)

BN

R/W

(0b1)

MESSAGE_TAG

Reserved

CFIFO Header

ADC Command

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

Reserved

ADC_REG_ADDRESS

ADC Command

Figure 18-28. Read Configuration Command Message Format for On-Chip ADC Operation

Table 18-35. On-Chip ADC Field Descriptions: Write Configuration

Field

Description

«
...
749
750
751
752
753
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Xantrex Страницы: 56

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Yamaha Страницы: 5

Бренд: YASKAWA Страницы: 42

Бренд: YASKAWA Страницы: 351

Бренд: Gardena Страницы: 15

Бренд: Rain Bird Страницы: 7

Бренд: Sices Страницы: 8

Бренд: Teradek Страницы: 10

Бренд: Monosem Страницы: 68

Frymaster YUM WINGSTREET K3000

Бренд: Welbilt Страницы: 16

Бренд: Advantech Страницы: 46

Бренд: Tektronix Страницы: 34

MICROMEGA CN77000 series

Бренд: Omega Страницы: 104

UltraVista 4K VWL-T122-4K-DP

Бренд: Rose electronics Страницы: 28

Бренд: Tascam Страницы: 14

Бренд: Progres Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды