Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 447 | Manualshive

Страница: 447 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-2

Freescale Semiconductor

12.1.1

Block Diagram

is a block diagram of the EBI. The signals shown are external pins to the MCU.

NOTE

Refer to in the Signals chapter, as not all signals are implemented in all
device packages. The last two columns in for a list of available signals on
the 324 package and the VertiCal assembly. The VertiCal assembly has ball
connections for all the

available

signals on the device.

The 324 package has a limited number of balls which affects the following EBI and calibration signals:

Table 12-1. MPC5565 324 Package Limitations

Features

MPC5565 Design

324 Package

Maximum 24-bit EBI address bus

ADDR[8:31]_GPIO[4:27]; ADDR[8:11] are muxed
as alternate signals with the chip select signals
CS[0:3]_ADDR[8:11]_GPIO[0:3]. ADDR[8:11] is
also muxed with GPIO[4:7], providing four chip
selects

and

24-bit address bits.

ADDR[8:11]_GPIO[4:7] no balls available.
Use CS[0:3]_ADDR[8:11]_GPIO[0:3] to
choose between using chip select signals

or

maximizing the number of output address
signals ADDR[8:31]_GPIO[0:3, 8:31] for a
24-bit EBI address bus.

Maximum 32-bits wide EBI data bus

DATA[0:31]_GPIO[28:59]

16 balls available for a 16-bit wide
DATA[0:15]_GPIO[28:43]. There are no balls
available for DATA[16:31]_GPIO[44:59].

Four EBI write enable/byte enable

WE/BE[0:3]

Two balls available (WE/BE[0:1])

EBI transfer error acknowledge

TEA_GPIO[71]

No ball available

EBI bus busy

BB signal not available

BB_GPIO[72] no ball available

EBI bus grant

BG signal not available

BG_GPIO[73] no ball available

Calibration bus

Calibration bus is separate from the EBI but uses
the EBI controller. Refer to for the calibration bus
signals.

No balls available. These signals are only
available in the VertiCal assembly.

«
...
445
446
447
448
449
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Falcon Страницы: 3

Бренд: Raymarine Страницы: 12

Бренд: Samson Страницы: 48

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

Бренд: HEIDENHAIN Страницы: 257

Бренд: Wittenstein Страницы: 52

Бренд: Rheem Страницы: 2

Бренд: Z-Wave Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: LOVATO ELECTRIC Страницы: 18

Бренд: ProMinent Страницы: 2

STM32F469 Series

Бренд: ST Страницы: 31

Revolution FA-M3 R

Бренд: YOKOGAWA Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды