Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1044 | Manualshive

Страница: 1044 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-51

Traditional BTM messages maintain their temporal ordering because each event that can cause a message
to be queued will enter the FIFO in the order it occurred and will be messaged out maintaining that order.

24.11.12.2 BTM Message Formats

The e200z6 Nexus3 module supports three types of traditional BTM messages—direct, indirect, and
synchronization messages. It supports two types of branch history BTM messages—indirect branch
history, and indirect branch history with synchronization messages. Debug status messages and error
messages are also supported.

24.11.12.2.1

Indirect Branch Messages (History)

Indirect branches include all taken branches whose destination is determined at run time, interrupts and
exceptions. If DC[PTM] is set, indirect branch information is messaged out in the following format:

Figure 24-29. Indirect Branch Message (History) Format

24.11.12.2.2

Indirect Branch Messages (Traditional)

If DC[PTM] is cleared, indirect branch information is messaged out in the following format:

Figure 24-30. Indirect Branch Message Format

HIST

MSB

LSB

2

3

4

U-ADDR

I-CNT

SRC

5

4 bits

1

TCODE (011100)

1-8 bits

1-32 bits

1-32 bits

6 bits

Max length = 82 bits; Min length = 13 bits

msb

LSB

2

3

4

U-ADDR

I-CNT

SRC

4 bits

1

TCODE (000100)

1-8 bits

1-32 bits

6 bits

Max length = 50 bits; Min length = 12 bits

«
...
1042
1043
1044
1045
1046
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Danfoss Страницы: 16

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 16

Бренд: Aurora Страницы: 2

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: Xylem Страницы: 2

Бренд: Quickie Страницы: 64

Бренд: Atari Страницы: 3

Бренд: FASAR ELETTRONICA Страницы: 2

Alicat Scientific MC

Бренд: Halma Страницы: 2

Бренд: Guangdong Schen Investment Страницы: 15

Бренд: ProMinent Страницы: 2

mikromedia for ARM

Бренд: mikroElektronika Страницы: 35

Triad Controls WE Series

Бренд: A-T Controls Страницы: 13

Бренд: Texas Instruments Страницы: 19

Бренд: Danfoss Страницы: 2

Бренд: StudioComm Страницы: 55

Бренд: Edge-Core Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды