Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 41

Страница: 41 / 1153

Introduction

MPC5565 Microcontroller Reference Manual, Rev. 1.0

1-6

Freescale Semiconductor

— Memory controller shared with EBI

— 16-bit data bus

— 21-bit address bus with no support for the least significant address bit (ADDR31)

— Up to 22 bit address space providing a 4 MB addressing range (the two most significant bits

shared with CAL_CS[2:3])

— Chip selects: up to three chip selects (CAL_CS[0] and CAL_CS[2:3] shared with

CAL_ADDR[10:11])

•

System integration unit (SIU)

— Centralized GPIO control of bus pins: 324 BGA package with 150 pins

— Centralized pad control on a per-pin basis

— System reset monitoring and generation

— External interrupt inputs, filtering and control

•

Error correction status module (ECSM)
Configurable error-correcting codes (ECC) reporting for internal SRAM and flash memories

•

On-chip flash

— Two MB burst flash memory

— 256 KB

64-bit configuration

— Censorship protection scheme to prevent flash content visibility

— Hardware read-while-write feature that can erase/program blocks while other blocks are read

(used for EEPROM emulation and data calibration)

— 20 blocks with sizes ranging from 16–128 KB to support features such as boot block, operating

system block, and EEPROM emulation. Blocks are structured as follows:

– 2 x 16 KB

– 2 x 48 KB

– 2 x 64 KB

– 14 x 128 KB

— Read while write with multiple partitions

— Page programming mode to support rapid end of line programming

— Hardware programming state machine

•

Configurable cache memory, 0–8 KB

— Two-way set-associative unified (instruction and data) cache

— Decouples processor performance from system memory performance

•

On-chip internal static RAM (SRAM)

— 80 KB general-purpose SRAM of which 32 KB are on standby power

— ECC performs single-bit correction, double-bit error detection

•

Boot assist module (BAM)

— Enables and manages the transition of MCU from reset to user code execution in the following

configurations:

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды