Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 901 | Manualshive

Страница: 901 / 1153

background image

Enhanced Serial Communication Interface (eSCI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

20-6

Freescale Semiconductor

23

PT

Parity type. Determines whether the eSCI generates and checks for even parity or odd parity. With even parity, an
even number of 1s clears the parity bit and an odd number of 1s sets the parity bit. With odd parity, an odd number
of 1s clears the parity bit and an even number of 1s sets the parity bit.
0 Even parity
1 Odd parity

24

TIE

Transmitter interrupt enable. Enables the transmit data register empty flag ESCI

x

_SR[TDRE] to generate interrupt

requests. The interrupt is suppressed in TX DMA mode.
0 TDRE interrupt requests disabled
1 TDRE interrupt requests enabled

25

TCIE

Transmission complete interrupt enable. Enables the transmission complete flag ESCIx_SR[TC] to generate
interrupt requests. The interrupt is suppressed in TX DMA mode.
0 TC interrupt requests disabled
1 TC interrupt requests enabled

26

RIE

Receiver full interrupt enable. Enables the receive data register full flag ESCIx_SR[RDRF] and the overrun flag
ESCIx_SR[OR] to generate interrupt requests. The interrupt is suppressed in RX DMA mode.
0 RDRF and OR interrupt requests disabled
1 RDRF and OR interrupt requests enabled

27

ILIE

Idle line interrupt enable. Enables the idle line flag ESCIx_SR[IDLE] to generate interrupt requests.
0 IDLE interrupt requests disabled
1 IDLE interrupt requests enabled

28

TE

Transmitter enable. Enables the eSCI transmitter and configures the TXD pin as being controlled by the eSCI. The
TE bit can be used to queue an idle preamble.
0 Transmitter disabled
1 Transmitter enabled

29

RE

Receiver enable. Enables the eSCI receiver.
0 Receiver disabled
1 Receiver enabled

30

RWU

Receiver wake-up. Standby state.
0 Normal operation.
1 RWU enables the wake-up function and inhibits further receiver interrupt requests. Normally, hardware wakes

the receiver by automatically clearing RWU.

31

SBK

Send break. Toggling SBK sends one break character (Refer to the description of ESCI

x

_CR2[BRK13] for break

character length). Toggling implies clearing the SBK bit before the break character has finished transmitting. As long
as SBK is set, the transmitter continues to send complete break characters.
0 No break characters
1 Transmit break characters

Table 20-3. ESCI

x

_CR1 Field Descriptions (continued)

Field

Description

«
...
899
900
901
902
903
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 50

Бренд: 3Ware Страницы: 2

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренд: RAM Страницы: 71

Бренд: ITALFARAD Страницы: 32

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Teledyne Страницы: 47

Бренд: Western Co Страницы: 14

Бренд: VMK Страницы: 98

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

Бренд: maxon motor Страницы: 44

Бренд: Cruisair Страницы: 30

Бренд: Midian Electronics Страницы: 22

Бренд: VADDIO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды