Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 1153

background image

Reset

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

4-9

4.4.2.3.4

Loss-of-Clock Reset

A loss-of-clock reset occurs when the FMPLL detects a failure in either the reference signal or FMPLL
output, and the loss-of-clock reset enable (LOCRE) bit in the FMPLL_SYNCR is set.

The device comes out of loss-of-clock reset using the following sequence:

1. Starting the internal reset signal asserts, as indicated by RSTOUT asserting, the value on the

WKPCFG pin is applied. At the same time, the PLLCFG[0:1] values are applied only if RSTCFG
is asserted.

2. After the FMPLL has a clock and is locked, the reset controller waits the predetermined clock

cycles before negating RSTOUT. When the clock count finishes, WKPCFG and BOOTCFG[0:1]
are sampled. BOOTCFG[0:1] is only sampled if RSTCFG asserts.

3. The reset controller then waits four clock cycles before negating RSTOUT and updating the fields

in SIU_RSR. The LCRS bit is set, and all other reset status bits in the SIU_RSR are cleared.

Refer to

Section 4.2.2, “Reset Output (RSTOUT)

Refer to

Section 11.4.2.6, “Loss-of-Clock Detection

,”

for more information on loss-of-clock.

4.4.2.3.5

Watchdog Timer/Debug Reset

The WDRS bit in the reset status register (SIU_RSR) is set when the watchdog timer or a debug request
reset occurs.

A watchdog timer reset occurs and the WDRS bit is set when all the following conditions occur:

•

e200z6 core watchdog timer is enabled with the enable next watchdog timer (EWT)

•

Watchdog timer interrupt status (WIS) bits are set in the timer status register (TSR)

•

Watchdog reset control (WRC) field in the timer control register (TCR) is configured to reset

•

Time-out occurs

The debug tool can issue a debug reset command by writing 2’b10 to the RST bit {DBCR0[2:3]} register
in the e200z6 core, which sets the WDRS bit in the reset status register of the systems integration unit
(SIU_RSR)

To determine if WDRS was set by a watchdog timer or debug reset, check the WRS field in the e200z6
core TSR.

The effect of a watchdog timer or debug reset request is the same on the reset controller.

The debug tool can also reset the device using one of the following methods:

•

Debug tool asserts the RESET signal on the RESET_b pin

•

Debug tool sets the software system reset (SSR) bit in the system reset control register
(SIU_SRCR)

The debug tool writes a one to the software external reset (SER) bit in the system reset control register
(SIU_SRCR) to generate an external software reset.

«
...
148
149
150
151
152
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Balboa Instruments Страницы: 10

Бренд: Barthelme Страницы: 8

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: Linear Technology Страницы: 32

EZ-ZONE PM L AAAAB Series

Бренд: Watlow Страницы: 30

Tunnel Master Jr

Бренд: ICS Страницы: 70

Бренд: Black Stone Страницы: 2

Бренд: Sysmac Страницы: 159

Бренд: Digital View Страницы: 35

Бренд: Badger Meter Страницы: 66

Бренд: Tapeswitch Страницы: 2

Бренд: SLV Страницы: 11

Бренд: Technische Alternative Страницы: 124

NetworkHD 200 series

Бренд: Wyrestorm Страницы: 4

Бренд: Tech Controllers Страницы: 20

Бренд: WAC Страницы: 5

Бренд: Unitech Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды