manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-71

If a closed gate is detected while no command transfers are taking place and the CFIFO status is triggered, 
the CFIFO status is immediately changed to IDLE, the SSS bit is negated, and the PF flag is asserted. If a 
closed gate is detected during the serial transmission of a command to the external device, it has no affect 
on the CFIFO status until the transmission completes. After the transmission is completed, the TC_CF 
counter is updated, the SSS bit is negated, the PF flag is asserted, and the CFIFO status is changed to IDLE. 
An asserted SSS bit and a level trigger are required to restart the CFIFO. Command transfers restart from 
the point they have stopped.

If the gate closes and opens during the same serial transmission of a command to the external device, it 
has no effect on the CFIFO status or on the PF flag, but the TORF flag asserts as shown in 

Figure 18-40

. 

Therefore, closing the gate for a period less than a serial transmission time interval does not guarantee that 
the closure affects command transfers from a CFIFO.

The pause bit has no effect in single-scan level trigger mode.

18.4.3.5.3

Continuous-Scan Mode

In continuous-scan mode, multiple passes looping through a sequence of command messages in a 
command queue are executed. When a CFIFO is programmed for a continuous-scan mode, the 
EQADC_CFCRn[SSE] (see 

Section 18.3.2.6, “eQADC CFIFO Control Registers 0–5 

(EQADC_CFCRn)

”) does not have any effect. 

Continuous-Scan Software Trigger

When a CFIFO is programmed to continuous-scan software trigger mode, the CFIFO is triggered 
immediately. The CFIFO commands start to be transferred when the CFIFO becomes the highest priority 
CFIFO using an available on-chip ADC or an external command buffer that is not full. When a CFIFO is 
programmed to run in continuous-scan software trigger mode, the eQADC does not halt transfers from the 
CFIFO until the CFIFO operation mode is modified to disabled or a higher priority CFIFO preempts it. 
Although command transfers do not stop upon detection of an asserted EOQ bit, the EOQF is set and, if 
enabled, an EOQ interrupt request is generated. 

The pause bit has no effect in continuous-scan software trigger mode.

Continuous-Scan Edge Trigger

When rising, falling, or either edge trigger mode is selected for a CFIFO, a corresponding edge on the 
associated ETRIG signal places the CFIFO in a TRIGGERED state. The CFIFO commands start to be 
transferred when the CFIFO becomes the highest priority CFIFO using an available on-chip ADC or an 
external command buffer that is not full.

When an EOQ or a pause is encountered, the eQADC halts command transfers from the CFIFO and, if 
enabled, the appropriate interrupt requests are generated. Another edge trigger event is required to resume 
command transfers but no software involvement is required to rearm the CFIFO to detect such event. 

A trigger overrun happens when the CFIFO is already in a TRIGGERED state and a new edge trigger event 
is detected.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Fantech ECO-TOUCH Operating Manual preview
ECO-TOUCH
Бренд: Fantech Страницы: 2
Galaxy Control Systems 635 Series Worksheet preview
635 Series
Бренд: Galaxy Control Systems Страницы: 5
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Бренд: Hanna Instruments Страницы: 88
Samson 2479 Mounting And Operating Instructions preview
2479
Бренд: Samson Страницы: 78
Radware Alteon Installation And Maintenance Manual preview
Alteon
Бренд: Radware Страницы: 98
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Бренд: Samwontech Страницы: 91
Watlow F4T Installation And Troubleshooting User’S Manual preview
F4T
Бренд: Watlow Страницы: 59
Watts Tekmar WiFi Snow Melting Control 670 Installation Manual preview
Tekmar WiFi Snow Melting Control 670
Бренд: Watts Страницы: 48
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 132
S&C IntelliCap Operation preview
IntelliCap
Бренд: S&C Страницы: 26
G&D PersonalWorkplace Pro Video Installation Manual preview
PersonalWorkplace Pro Video
Бренд: G&D Страницы: 56
ACTi R12CP-30 Installation Manual preview
R12CP-30
Бренд: ACTi Страницы: 20
SOARNEX EWC-100 Quick Installation Manual preview
EWC-100
Бренд: SOARNEX Страницы: 14
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Бренд: Neousys Technology Страницы: 101
Samson 3375 Mounting And Operating Instructions preview
3375
Бренд: Samson Страницы: 130
Ulvac UK-2 Instruction Manual preview
UK-2
Бренд: Ulvac Страницы: 48
YASKAWA SI-T/ V7 Technical Manual preview
SI-T/ V7
Бренд: YASKAWA Страницы: 157
LOVATO ELECTRIC ATL800 Installation Manual preview
ATL800
Бренд: LOVATO ELECTRIC Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды