Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 695 | Manualshive

Страница: 695 / 1153

background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

17-40

Freescale Semiconductor

Table 17-25. ETPU_C

n

CR Field Descriptions

Field

Description

0

CIE

Channel interrupt enable. This bit is mirrored from the ETPU_CIER
0 Disable interrupt for this channel.For more information, refer to the

eTPU Reference Manual

.

1 Enable interrupt for this channel.

1

DTRE

Channel data transfer request enable. This bit is mirrored from the ETPU_CDTRER.
0 Disable data transfer request for this channel.Refer to the

eTPU Reference Manual

for more information.

1 Enable data transfer request for this channel.

2–3

CPR

[0:1]

Channel priority. Defines the priority level for the channel. The priority level is used by the hardware scheduler. The
values for CPR[1:0] and corresponding levels are shown in the table below.

For more information on the hardware scheduler, refer to the

eTPU Reference Manual

.

4–5

Reserved.

6

ETPD

This bit selects which channel signal, input or output, is used in the entry point selection. The ETPD value has to be
compatible with the function chosen for the channel, selected in the field CFS. For details about entry table and
condition encoding schemes, refer to the

eTPU Reference Manual

. The ETPD bit is only present in the MPC5565

and MPC5567.
0 Use PSTI for entry point selection.
1 Use PSTO for entry point selection.

7

ETCS

Entry table condition select. Determines the channel condition encoding scheme that selects the entry point to be
taken in an entry table. The ETCS value has to be compatible with the function chosen for the channel, selected in
ETPU_C

n

CR[CFS]. Two condition encoding schemes are available.

1 Select alternate entry table condition encoding scheme.
0 Select standard entry table condition encoding scheme.For details about entry table and condition encoding

schemes, refer to the

eTPU Reference Manual

.

8–10

Reserved.

11–15

CFS
[0:4]

Channel function select. Defines the function to be performed by the channel. The function assigned to the channel
has to be compatible with the channel condition encoding scheme, selected by ETPU_C

n

CR[ETCS]. For more

information about functions, refer to the

eTPU Reference Manual

.

16

ODIS

Output disable. Enables the channel to have its output forced to the value opposite to OPOL when the output disable
input signal corresponding to the channel group that it belongs is active.
0 Turns off the output disable feature for the channel.For more information on output disable, refer to the

eTPU

Reference Manual

.

1 Turns on the output disable feature for the channel

17

OPOL

Output polarity. Determines the output signal polarity. The activation of the output disable signal forces, when
enabled by ETPU_C

n

CR[ODIS], the channel output signal to the opposite of this polarity.

0 Output active low (output disable drives output to high)
1 Output active high (output disable drives output to low)

CPR

Priority

00

Disabled

01

Low

10

Middle

11

High

«
...
693
694
695
696
697
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: OEG Страницы: 168

Бренд: QCON Страницы: 4

Бренд: Garmin Страницы: 4

Бренд: IAI Страницы: 5

Бренд: Velleman Страницы: 12

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Trane Technologies Страницы: 8

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Бренд: Hoffer Страницы: 57

Бренд: Samson Страницы: 44

Бренд: Beckhoff Страницы: 47

Бренд: DOTECH Страницы: 4

Бренд: MISUMI Страницы: 166

Бренд: Sunricher Страницы: 2

Бренд: Sorel Страницы: 20

Бренд: Parker Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды