manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Serial Communication Interface (eSCI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0 

Freescale Semiconductor

20-13

20.3.3.6

LIN Transmit Register (ESCI

x

_LTR)

ESCI

x

_LTR can be written to only when TXRDY is set. The first byte written to the register selects the 

transmit address, the second byte determines the frame length, the third and fourth byte set various frame 
options and determine the timeout counter. Header parity is automatically generated if the 
ESCI

x

_LCR[PRTY] bit is set. For TX frames, the fourth byte (bits T7–T0) is skipped, since the timeout 

function does not apply. All following bytes are data bytes for the frame. CRC and checksum bytes are 
automatically appended when the appropriate options are selected.

When a bit error is detected, an interrupt is set and the transmission aborted. The register can only be 
written again after the interrupt is cleared. Afterwards a new frame starts, and the first byte needs to contain 
a header again. 

Additionally it is possible to flush the ESCI

x

_LTR by setting the ESCI

x

_LCR[LRES] bit.

NOTE

Not all values written to the ESCI

x

_LTR generate valid LIN frames. The 

values are determined according to the LIN specification.

7

LIN

LIN mode. Switch device into LIN mode. 
0 LIN disabled
1 LIN enabled

8

RXIE

LIN RXREG ready interrupt enable. Generates an Interrupt when new data is available in the LIN RXREG. For a list 
of interrupt enables and flags, Refer to 

Table 20-21

.

9

TXIE

LIN TXREG ready interrupt enable. Generates an Interrupt when new data can be written to the LIN TXREG. For a 
list of interrupt enables and flags, Refer to 

Table 20-21

.

10

WUIE

RX wake-up interrupt enable. Generates an Interrupt when a wake-up flag from a LIN slave has been received. For 
a list of interrupt enables and flags, Refer to 

Table 20-21

.

11

STIE

Slave timeout error interrupt enable. Generates an Interrupt when the slave response is too slow. For a list of interrupt 
enables and flags, Refer to 

Table 20-21

.

12

PBIE

Physical bus error interrupt enable. Generates an Interrupt when no valid message can be generated on the bus. For 
a list of interrupt enables and flags, Refer to 

Table 20-21

.

13

CIE

CRC error interrupt enable. Generates an Interrupt when a CRC error on a received extended frame is detected. For 
a list of interrupt enables and flags, Refer to 

Table 20-21

.

14

CKIE

Checksum error interrupt enable. Generates an Interrupt on a detected checksum error. For a list of interrupt enables 
and flags, Refer to 

Table 20-21

.

15

FCIE

Frame complete interrupt enable. Generates an Interrupt after complete transmission of a TX frame, or after the last 
byte of an RX frame is received. (The complete frame includes all header, data, CRC and checksum bytes as 
applicable.) For a list of interrupt enables and flags, Refer to 

Table 20-21

.

16–22

Reserved.

23

OFIE

Overflow interrupt enable. Generates an Interrupt when a data byte in the ESCIx_LRR has not been read before the 
next data byte is received. For a list of interrupt enables and flags, Refer to 

Table 20-21

.

24–31

Reserved.

Table 20-7. ESCI

x

_LCR Field Descriptions (continued)

Field

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
3Ware 7000-2 - Escalade RAID Controller Features preview
7000-2 - Escalade RAID Controller
Бренд: 3Ware Страницы: 2
Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Lawler 801 Installation & Maintenance Manual preview
801
Бренд: Lawler Страницы: 4
QTP 10900 Quick Start Manual preview
10900
Бренд: QTP Страницы: 2
phytron MCC-2 Manual preview
MCC-2
Бренд: phytron Страницы: 55
Sonos Controller CR100 Brochure & Specs preview
Controller CR100
Бренд: Sonos Страницы: 2
Powtran PR5200 Series Manual preview
PR5200 Series
Бренд: Powtran Страницы: 36
D-M-E VCTB-4000 User Manual preview
VCTB-4000
Бренд: D-M-E Страницы: 15
Alcor Micro AU9540 Technical Reference Manual preview
AU9540
Бренд: Alcor Micro Страницы: 18
PPI Zenex Plus User Manual preview
Zenex Plus
Бренд: PPI Страницы: 27
Zamel RTD-02 Manual Instruction preview
RTD-02
Бренд: Zamel Страницы: 2
Yaesu G-450A User Manual preview
G-450A
Бренд: Yaesu Страницы: 15
Milesight UC50 Series User Manual preview
UC50 Series
Бренд: Milesight Страницы: 28
Kele UCM-420A Operating And Installation Instructions preview
UCM-420A
Бренд: Kele Страницы: 33
YASKAWA MP23 Series Manual preview
MP23 Series
Бренд: YASKAWA Страницы: 23
AudioCodes Mediant 4000B Quick Setup Manual preview
Mediant 4000B
Бренд: AudioCodes Страницы: 10
Gira 0566 Series Installation Instructions preview
0566 Series
Бренд: Gira Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды