manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

9-25

128–159 

0x10 [0:31]

DADDR

[0:31]

Destination address. Memory address pointing to the destination data.

160 

0x14 [0]

CITER.E_LINK

Enable channel-to-channel linking on minor loop completion. As the channel completes 
the inner minor loop, this flag enables the linking to another channel, defined by 
CITER.LINKCH[0:5]. The link target channel initiates a channel service request via an 
internal mechanism that sets the TCD.START bit of the specified channel. If channel 
linking is disabled, the CITER value is extended to 15 bits in place of a link channel 
number. If the major loop is exhausted, this link mechanism is suppressed in favor of the 
MAJOR.E_LINK channel linking. 
0 The channel-to-channel linking is disabled.
1 The channel-to-channel linking is enabled.

Note:  

This bit must be equal to the BITER.E_LINK bit otherwise a configuration error is 

reported.

161–166 

0x14 [1:6]

CITER

[0:5]

or

CITER.LINKCH

[0:5]

Current “major” iteration count or link channel number. 
If channel-to-channel linking is disabled (TCD.CITER.E_LINK = 0), then 
 • No channel-to-channel linking (or chaining) is performed after the inner minor loop is 

exhausted. TCD bits [161:175] are used to form a 15-bit CITER field.

otherwise
 • After the minor loop is exhausted, the eDMA engine initiates a channel service request 

at the channel defined by CITER.LINKCH[0:5] by setting that channel’s TCD.START 
bit.

167–175 

0x14 [7:15]

CITER

[6:14]

Current “major” iteration count. This 9 or 15-bit count represents the current major loop 
count for the channel. It is decremented each time the minor loop is completed and 
updated in the transfer control descriptor memory. After the major iteration count is 
exhausted, the channel performs a number of operations (for example, final source and 
destination address calculations), optionally generating an interrupt to signal channel 
completion before reloading the CITER field from the beginning iteration count (BITER) 
field.

Note:  

 When the CITER field is initially loaded by software, it must be set to the same 

value as that contained in the BITER field.

Note:  

If the channel is configured to execute a single service request, the initial values 

of BITER and CITER must be 0x0001.

176–191 

0x14 [16:31]

DOFF

[0:15]

Destination address signed offset. Sign-extended offset applied to the current destination 
address to form the next-state value as each destination write is completed.

192–223 

0x18 [0:31]

DLAST_SGA

[0:31]

Last destination address adjustment or the memory address for the next transfer control 
descriptor to be loaded into this channel (scatter/gather).
If scatter/gather processing for the channel is disabled (TCD.E_SG = 0) then
 • Adjustment value added to the destination address at the completion of the outer major 

iteration count. 

This value can be applied to “restore” the destination address to the initial value, or adjust 
the address to reference the next data structure.
Otherwise
 • This address points to the beginning of a 0-modulo-32 byte region containing the next 

transfer control descriptor to be loaded into this channel. This channel reload is 
performed as the major iteration count completes. The scatter/gather address must be 
0-modulo-32 byte, otherwise a configuration error is reported.

Table 9-19. TCD

n

 Field Descriptions (continued)

Bits

Word Offset 

[n:n]

Field Name

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

KELCO F60 Installation Instructions Manual preview
F60
Бренд: KELCO Страницы: 36
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Бренд: ECKELMANN Страницы: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Бренд: H3C Страницы: 17
H3C WX Series Getting Started Manual preview
WX Series
Бренд: H3C Страницы: 32
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Бренд: Parker Страницы: 44
National Instruments RMC-8354 User Manual preview
RMC-8354
Бренд: National Instruments Страницы: 102
NAU ROBOTICS RC40A Operating Instruction preview
RC40A
Бренд: NAU ROBOTICS Страницы: 109
Native Instruments Maschine Mikro MK2 Getting Started preview
Maschine Mikro MK2
Бренд: Native Instruments Страницы: 181
Omega PHCN-37 User Manual preview
PHCN-37
Бренд: Omega Страницы: 56
Omega DP25-TC Quick Start Manuals preview
DP25-TC
Бренд: Omega Страницы: 2
ZKTeco SpeedFace-V3L Quick Start Manual preview
SpeedFace-V3L
Бренд: ZKTeco Страницы: 14
Unico 11100 Installation And Troubleshooting Manual preview
11100
Бренд: Unico Страницы: 164
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Бренд: IBC Страницы: 8
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Бренд: UCS Страницы: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Бренд: Curtis Страницы: 41
Zamel RTD-02 Manual Instruction preview
RTD-02
Бренд: Zamel Страницы: 2
Yaesu G-450A User Manual preview
G-450A
Бренд: Yaesu Страницы: 15
Milesight UC50 Series User Manual preview
UC50 Series
Бренд: Milesight Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды