Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 741 | Manualshive

Страница: 741 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-42

Freescale Semiconductor

NOTE

If TBC_CLK_PS is not set to disabled, it must not be changed to any other
value besides disabled. If TBC_CLK_PS is set to disabled it can be changed
to any other value.

18.3.3.3

ADC Time Base Counter Registers (ADC_TBCR)

The ADC_TBCR contains the current value of the time base counter. ADC_TBCR can be accessed by
configuration commands sent to ADC0 or to ADC1. A data write to ADC_TBCR using a configuration
command sent to ADC0 writes the same memory location as a write using a configuration command sent
to ADC1.

NOTE

Simultaneous write accesses from ADC0 and ADC1 to ADC_TBCR are not
allowed.

18.3.3.4

ADC

n

Gain Calibration Constant Registers (ADC0_GCCR and

ADC1_GCCR)

The ADC

n

_GCCR contains the gain calibration constant used to fine-tune the ADC

n

conversion results.

Refer to

Section 18.4.5.4, “ADC Calibration Feature

,” for details about the calibration scheme used in the

eQADC.

Address: 0x03

Access: Read/Write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

TBC_VALUE

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 18-21. ADC Time Base Counter Register (ADC_TBCR)

Table 18-31. ADC_TBCR Field Descriptions

Field

Description

0–15

TBC_

VALUE

[0:15]

Time base counter VALUE. Contains the current value of the time base counter. Reading TBC_VALUE returns the
current value of time base counter. Writes to TBC_VALUE register load the written data to the counter. The time base
counter counts from 0x0000 to 0xFFFF and wraps when reaching 0xFFFF.

«
...
739
740
741
742
743
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Magnescale Страницы: 3

Бренд: Danfoss Страницы: 30

Бренд: Securi-Prod Страницы: 3

Бренд: CORNING Страницы: 142

Enclosure ENCR-10

Бренд: suprema Страницы: 18

Бренд: E+L Страницы: 62

Бренд: Omicron Страницы: 17

Бренд: Simplex Страницы: 12

Бренд: Martin Audio Страницы: 1

Legend LX Second Stage

Бренд: Aqua Lung Страницы: 18

Бренд: BCH Electric Страницы: 452

GALATIC STAR 19C

Бренд: American DJ Страницы: 1

Бренд: Cairox Страницы: 3

Бренд: Toky Страницы: 4

Бренд: Ingersoll-Rand Страницы: 8

Jetstream Classic

Бренд: POSEIDON Страницы: 25

Бренд: Taconova Страницы: 24

SuperFlow 350 Regulator

Бренд: Kirby Morgan Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды