Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 641 | Manualshive

Страница: 641 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-64

Freescale Semiconductor

shows the operation of the output disable feature in OPWFMB mode. Unlike OPWFM mode,

the output disable forces the channel output flip-flop to the EDPOL bit value. This functionality targets
applications that use active high signals and a high to low transition at A1 match. For such cases, clear
EDPOL to 0.

Figure 16-47. eMIOS OPWFMB Mode Example — Active Output Disable

The output disable has a synchronous operation, meaning that the assertion of the output disable input
signal causes the channel output flip-flop to transition to EDPOL at the next system clock cycle. If the
output disable input is negated, the output flip-flop transitions at the following A1 or B1 match.

it is assumed that the output disable input is enabled and selected for the channel (refer to

Section 16.3.1.7, “eMIOS Channel Control Register (EMIOS_CCRn),”

for a detailed description of the

ODIS and ODISSL bits and selection of the output disable inputs).

The FORCMA and FORCMB bits allow the software to force the output flip-flop to the level
corresponding to a match on comparators A or B respectively. Similar to a B1 match, FORCMB clears the
internal counter. The FLAG bit is not set when the FORCMA or FORCMB bits are set.

Cycle n

Cycle n+1

Cycle n+2

A1 value

B1 value

B2 value

0x000008

0x000002

0x000006

0x000008

0x000001

EMIOS_CCNTR

n

0x000004

0x000006

MODE[0] = 1

A2 value

0x000002

0x000004

0x000006

0x000002

0x000004

0x000006

0x000008

0x000006

Output flip-flop

Write to B2

Match A1

Match B1

Match B1

A1/B1 load signal

Due to B1 match

FLAG set event

cycle n-1

Time

Write to A2

Match A1

Write to A2

Match B1

EDPOL = 0

«
...
639
640
641
642
643
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Garmin Страницы: 4

Ambience Control 1

Бренд: EuroLite Страницы: 20

Бренд: SKF Страницы: 88

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: ST Страницы: 40

Бренд: Varian Страницы: 37

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: Zonex Страницы: 16

Бренд: TAC Vista Страницы: 2

Бренд: Ellard Страницы: 21

Бренд: Topcon Страницы: 9

Бренд: Aerotech Страницы: 36

Бренд: Duke Страницы: 4

Бренд: Zmotion Страницы: 59

Бренд: ELMARK Страницы: 7

Бренд: Qanon Страницы: 10

DeltaSol MiniPool

Бренд: Resol Страницы: 16

Бренд: Sinclair Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды