Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 419 | Manualshive

Страница: 419 / 1153

background image

Frequency Modulated Phase Locked Loop and System Clocks (FMPLL)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

11-8

Freescale Semiconductor

11.1.2

Overview

The frequency modulated phase locked loop (FMPLL) allows the user to generate high speed system
clocks from an 8–20 MHz crystal oscillator or from an external clock generator. Further, the FMPLL
supports programmable frequency modulation of the system clock. The FMPLL multiplication factor,
reference clock pre-divider factor, output clock divider ratio, modulation depth, and modulation rate are
all controllable through a bus interface.

11.1.3

Features

The FMPLL has the following major features:

•

Input clock frequency from 8–20 MHz

•

Current controlled oscillator (ICO) range from 48 MHz to maximum device frequency

•

Reference frequency pre-divider (PREDIV) for finer frequency synthesis resolution

•

Reduced frequency divider (RFD) for reduced frequency operation without forcing the FMPLL to
re-lock

•

Four modes of operation:

— Bypass mode.

— Crystal reference mode. This is the default mode for the 324 (with or without the 496 assembly)

package. Refer to

Section 11.1.4.1, “Crystal Reference (Default Mode)

.”

— External reference mode. Refer to

Section 11.1.4.2, “External Reference Mode

— PLL dual-controller (1:1) mode for EXTAL_EXTCLK to CLKOUT skew minimization.

•

Programmable frequency modulation

— Modulation enabled/disabled via bus interface

— Triangle wave modulation

— Register programmable modulation depth (±1% to ±2% deviation from center frequency)

— Register programmable modulation frequency dependent on reference frequency; limited to

100–250 MHz.

•

Lock detect circuitry reports when the FMPLL has achieved frequency lock and continuously
monitors lock status to report loss of lock conditions

— User-selectable ability to generate an interrupt request upon loss of lock.

Refer to

Chapter 10, “Interrupt Controller (INTC)

,” for details.

— User-selectable ability to generate a system reset upon loss of lock.

Refer to

Chapter 4, “Reset

,” for details.

•

Loss-of-clock (LOC) detection for reference and feedback clocks

— User-selectable ability to generate an interrupt request upon loss of clock.

Refer to

Chapter 10, “Interrupt Controller (INTC)

,” for details.

— User-selectable ability to generate a system reset upon loss of clock

Refer to

Chapter 4, “Reset

,” for details.

•

Self-clocked mode (SCM) operation in event of input clock failure

«
...
417
418
419
420
421
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Hach Страницы: 86

Бренд: 3M Страницы: 34

Бренд: Uclear Страницы: 40

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

Бренд: z21 Страницы: 2

Бренд: Maximum Controls Страницы: 58

Бренд: Atari Страницы: 3

Бренд: VALPES Страницы: 28

Бренд: Jung Страницы: 8

Бренд: Danfoss Страницы: 6

Sigma II Series

Бренд: YASKAWA Страницы: 359

Keystation 61es

Бренд: M-Audio Страницы: 15

Бренд: H3C Страницы: 32

Бренд: Bamo Страницы: 10

Бренд: Wahlberg Страницы: 40

Бренд: Kamado Joe Страницы: 2

Бренд: Nibe Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды