Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 789 | Manualshive

Страница: 789 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-90

Freescale Semiconductor

18.4.5.3

Time Stamp Feature

The on-chip ADCs can provide a time stamp for the conversions they execute. A time stamp is the value
of the time base counter latched when the eQADC detects the end of the analog input voltage sampling. A
time stamp for a conversion command is requested by setting the TSR bit in the corresponding command.
When TSR is negated, that is a time stamp is not requested, the ADC returns a single result message
containing the conversion result. When TSR is asserted, that is a time stamp is requested, the ADC returns
two result messages; one containing the conversion result, and another containing the time stamp for that
conversion. The result messages are sent in this order to the RFIFOs and both messages are sent to the
same RFIFO as specified in the MESSAGE_TAG field of the executed conversion command.

The time base counter is a 16-bit up counter and wraps after reaching 0xFFFF. It is disabled after reset and
it is enabled according to the setting of ADC_TSCR[TBC_CLK_PS] field (see

Section 18.3.3.2, “ADC

Time Stamp Control Register (ADC_TSCR)

”). TBC_CLK_PS defines if the counter is enabled or

disabled, and, if enabled, at what frequency it is incremented. The time stamps are returned regardless of
whether the time base counter is enabled or disabled. The time base counter can be reset by writing 0x0000
to the ADC_TBCR (

Section 18.3.3.3, “ADC Time Base Counter Registers (ADC_TBCR)

”) with a write

configuration command.

18.4.5.4

ADC Calibration Feature

18.4.5.4.1

Calibration Overview

The eQADC provides a calibration scheme to remove the effects of gain and offset errors from the results
generated by the on-chip ADCs. Only results generated by the on-chip ADCs are calibrated. The results
generated by ADCs on the external device are directly sent to RFIFOs unchanged. The main component
of calibration hardware is a multiply-and-accumulate (MAC) unit, one per on-chip ADC, that is used to
calculate the following transfer function which relates a calibrated result to a raw, uncalibrated one.

CAL_RES = GCC * R OCC + 2;

where:

•

CAL_RES is the calibrated result corresponding the input voltage V

i

.

•

GCC is the gain calibration constant.

•

RAW_RES is the raw, uncalibrated result corresponding to an specific input voltage V

i

.

•

OCC is the offset calibration constant.

0b11110

62

1.94 129

121

0b11111

64

1.88 125

117

Table 18-47. ADC Clock Configuration Example (System Clock Frequency = 120 MHz)

ADC0/1_CLK_PS[0:4]

System Clock

Divide Factor

ADC Clock in MHz

(System Clock =

120MHz)

Differential Conversion

Speed with Default

Sampling Time

(13 +

2 cycles) in

ksamp/s

Single-Ended

Conversion Speed with

Default Sampling Time

(14 +

2 cycles) in

ksamp/s

«
...
787
788
789
790
791
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Zeagle Страницы: 37

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Mitsubishi Страницы: 30

Бренд: Teledyne Страницы: 102

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

Бренд: bluelab Страницы: 39

SmarTemp Control fx

Бренд: Webasto Страницы: 8

StarSign Bio Token 3.0 M

Бренд: Giesecke & Devrient Страницы: 28

Бренд: Parker Страницы: 24

Бренд: Cruisair Страницы: 30

SMC-3 150-C30NBD

Бренд: AB Quality Страницы: 4

Бренд: Badger Meter Страницы: 66

Бренд: CDVI Страницы: 24

DECORA ILLUMATECH IPF01-1LX

Бренд: Leviton Страницы: 2

Бренд: InnoMedia Страницы: 10

Бренд: Martin Audio Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды