manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-4

Freescale Semiconductor

 

•

eTPU development support features (NSEDI)

— IEEE-ISTO 5001-2002 standard Class 3 compliant for the eTPU engine.

— Data trace via data write messaging and data read messaging. This allows the development tool 

to trace reads and writes to selected shared parameter RAM (SPRAM) address ranges. Four 
data trace windows are shared by the two eTPU engines.

— Ownership trace via ownership trace messaging (OTM). OTM facilitates ownership trace by 

providing visibility of which channel is being serviced. An ownership trace message is 
transmitted to indicate when a new channel service request is scheduled, allowing the 
development tools to trace task flow. A special OTM is sent when the engine enters in idle state, 
meaning that all requests were serviced and no new requests are yet scheduled.

— Program trace via branch trace messaging. BTM displays program flow discontinuities (start, 

jumps, return, etc.), allowing the development tool to interpolate what transpires between the 
discontinuities. Thus static code can be traced. The branch trace messaging method uses the 
branch/predicate method to reduce the number of generated messages.

— Watchpoint messaging via the auxiliary port. WPM provides visibility of the occurrence of the 

eTPU’s watchpoints and breakpoints.

— Nexus based breakpoint/watchpoint configuration and single step support.

•

Run-time access to the on-chip memory map via the Nexus read/write access protocol. This feature 
supports accesses for run-time internal visibility, calibration variable acquisition, calibration 
constant tuning, and external rapid prototyping for powertrain automotive development systems.

•

All features are independently configurable and controllable via the IEEE

®

 1149.1 I/O port.

•

The NDI block reset is controlled with JCOMP, power-on reset, and the TAP state machine. These 
sources are independent of system reset.

•

System clock locked status indication via MDO0 following power-on reset.

24.1.3

Modes of Operation

The NDI block is in reset when the TAP controller state machine is in the TEST-LOGIC-RESET state. The 
TEST-LOGIC-RESET state is entered on the assertion of the power-on reset signal, negation of JCOMP, 
or through state machine transitions controlled by TMS. Assertion of JCOMP allows the NDI to move out 
of the reset state, and is a prerequisite to grant Nexus clients control of the TAP. Ownership of the TAP is 
achieved by loading the appropriate enable instruction for the desired Nexus client in the JTAGC controller 
(JTAGC) block when JCOMP is asserted.

Following negation of power-on reset, the NPC remains in reset until the system clock achieves lock. In 
PLL bypass mode, the NDI can transition out of the reset state immediately following negation of 
power-on reset. Refer to 

Section 24.4.5, “System Clock Locked Indication

” for more details.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Aalborg DFC Operating Manual preview
DFC
Бренд: Aalborg Страницы: 48
Fairchild 1600A Installation, Operation And Maintenance Instructions preview
1600A
Бренд: Fairchild Страницы: 2
Fairford synergy User Manual preview
synergy
Бренд: Fairford Страницы: 233
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Бренд: Gardena Страницы: 14
Gardena 1273 Operating Instructions preview
1273
Бренд: Gardena Страницы: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Бренд: Gantner Страницы: 4
YOKOGAWA CX1000 Installation And Connection Manual preview
CX1000
Бренд: YOKOGAWA Страницы: 2
Halma ALICAT SCIENTIFIC PC Quick Start Manual preview
ALICAT SCIENTIFIC PC
Бренд: Halma Страницы: 2
Halma ALICAT SCIENTIFIC PCD Operating Manual preview
ALICAT SCIENTIFIC PCD
Бренд: Halma Страницы: 46
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Бренд: WAC Страницы: 5
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Бренд: H.E. Anderson Страницы: 11
Watts WFHC 06Z 02 HC RF 24 User Manual preview
WFHC 06Z 02 HC RF 24
Бренд: Watts Страницы: 18
Texas Instruments Errata MSP430F6779 Manual preview
Errata MSP430F6779
Бренд: Texas Instruments Страницы: 27
ccei MPZ Technical Instructions preview
MPZ
Бренд: ccei Страницы: 16
Universal Remote Control total control MRX-10 Owner'S Manual preview
total control MRX-10
Бренд: Universal Remote Control Страницы: 16
Progeny Crystal.PoE V4 Manual preview
Crystal.PoE V4
Бренд: Progeny Страницы: 4
Sorel SBMC Installation And Operating Instructions Manual preview
SBMC
Бренд: Sorel Страницы: 20
FAAC AT- 4/868 UHF Installation Manual preview
AT- 4/868 UHF
Бренд: FAAC Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды