Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1063 | Manualshive

Страница: 1063 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-70

Freescale Semiconductor

4. The data can then be read from the burst data buffer (read/write access data register) through the

access method outlined in

Section 24.11.10, “ NZ6C3 Register Access via JTAG / OnCE

,” using

the Nexus register index of 0xA (refer to

5. Repeat step 3 until all doubleword values are read from the buffer.

NOTE

The data values must be shifted out 32-bits at a time lsb first (that is,
doubleword read = two word reads from the RWD).

NOTE

The actual RWA value as well as the CNT field within the RWCS are not
changed when executing a block read access (burst or non-burst). The
original values can be read by the external development tool at any time.

24.11.15.7 Error Handling

The NZ6C3 module handles various error conditions as follows:

24.11.15.7.1 System Bus Read/Write Error

All address and data errors that occur on read/write accesses to the e200z6 system bus will return a transfer
error. If this occurs:

1. The access is terminated without re-trying (AC bit is cleared).

2. The ERR bit in the RWCS register is set.

3. The error message is sent (TCODE = 8) indicating read/write error.

24.11.15.7.2 Access Termination

The following cases are defined for sequences of the read/write protocol that differ from those described
in the above sections:

1. If the AC bit in the RWCS register is set to start read/write accesses and invalid values are loaded

into the RWD and/or RWA, then a system bus access error may occur. This is handled as described
above.

2. If a block access is in progress (all cycles not completed), and the RWCS register is written, then

the original block access is terminated at the boundary of the nearest completed access.

a) If the RWCS is written with the AC bit set, the next read/write access will begin and the RWD

can be written to/ read from.

b) If the RWCS is written with the AC bit cleared, the read/write access is terminated at the nearest

completed access. This method can be used to break (early terminate) block accesses.

«
...
1061
1062
1063
1064
1065
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: KEB Страницы: 16

Бренд: Danfoss Страницы: 8

Бренд: LAB-EL Страницы: 25

Бренд: Swagelok Страницы: 20

Бренд: NXP Semiconductors Страницы: 362

lyriQ AU7394 Series

Бренд: On-Q Страницы: 8

Бренд: Zareba Страницы: 40

Hauser COMPAX-M Series

Бренд: Parker Страницы: 84

Бренд: Danfoss Страницы: 44

DynaFlow A12233

Бренд: Ransburg Страницы: 10

Бренд: Delta Regis Страницы: 15

Chipcon Products CC1110DK

Бренд: Texas Instruments Страницы: 3

Бренд: Teracom Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды