manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Calibration

MPC5565 Microcontroller Reference Manual, Rev. 1.0 

B-6

Freescale Semiconductor

Furthermore, the suppression of reflections from the non-calibration bus onto the calibration bus is not 
enabled by CRSE. Those reflections are also always suppressed. 

Refer to 

Section B.7.1, “Enabling Calibration Reflection Suppression

,” for when to set SIU_CCR[CRSE] 

or leave it in its reset negated state.

B.7

Application Information

B.7.1

Enabling Calibration Reflection Suppression

Set SIU_CCR[CRSE] to suppress reflections when calibrating. The calibration reflection suppression 
logic for an output that does not return to a negated state at the end of an access can introduce a small glitch 
on the output at the end of the access. The glitch does not interfere with the output valid or hold times. 
However, keep SIU_CCR[CRSE] in its reset negated state when not calibrating to prevent a glitch on the 
non-calibration bus outputs.

B.7.2

Communication With Development Tool Using I/O

The development tool can require some I/Os for communication between the MCU and the development 
tool on the VertiCal connector. Because the application can not use these pins in the 208 and 324 pin 
packages, they can be used for development tool use in a VertiCal connector. 

B.7.3

Matching Access Delay to Internal Flash With Calibration Memory

One use of VertiCal in the Automotive environment is engine calibration. For this application, an SRAM 
Top Board is added onto the VertiCal connector. This allows the engine calibrator to modify settings in 
SRAM, possibly using the Nexus interface or even by using the SCI port or a CAN interface.

Refer to 

Table 13-2

“Internal Flash External Emulation Mode.”

After the data is calibrated, it can be copied into the internal flash. The internal flash can be accessed faster 
than the calibration memory and this change in calibration data access time could change the overall 
system performance. To mitigate this change in system performance, the internal flash memory includes a 
feature that allows accesses to portions of the flash to be slowed down by adding extra wait states. This is 
done by multiply mapping the internal flash at different locations with different number of wait states. For 
example, the physical address of the flash array is 0x0000_0000 to 0x00FF_FFFF (depending on array 
size). That same flash data can be accessed at address 0x0100_0000 to 0x01FF_FFFF but accesses are one 
clock cycle slower. That same flash data can be accessed at addresses 0x0200_0000 to 0x02FF_FFFF but 
accesses are two clock cycles slower. This pattern is repeated through the memory map to addresses 
0x1F00_0000 to 0x1FFF_FFFF where accesses are 31 clock cycles slower.

The application would use this feature by mapping the calibration data to a region of the flash memory that 
has access timing to match the timing of the calibration RAM used when calibrating the data. This 
remapping of calibration data can be achieved by either using the translation feature of the MMU or 
rebuilding the code with a modified link file.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

GE 400 Series Installation Instructions preview
400 Series
Бренд: GE Страницы: 2
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Бренд: Fairchild Страницы: 2
Warren Controls E024 Installation, Operation And Maintenance Instructions preview
E024
Бренд: Warren Controls Страницы: 28
EAS Electric ECRP86EKD Operating Manual preview
ECRP86EKD
Бренд: EAS Electric Страницы: 89
KAESER KOMPRESSOREN SIGMA CONTROL 2 User Manual preview
SIGMA CONTROL 2
Бренд: KAESER KOMPRESSOREN Страницы: 246
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Бренд: YOKOGAWA Страницы: 150
National Instruments PXI-8150B User Manual preview
PXI-8150B
Бренд: National Instruments Страницы: 78
Click2Enter Click2Enter-I Operating & Installation Instructions Manual preview
Click2Enter-I
Бренд: Click2Enter Страницы: 34
Cooper S225-50-45 Service Information preview
S225-50-45
Бренд: Cooper Страницы: 4
Gantner GAT Access 6600 Series Quick Start Manual preview
GAT Access 6600 Series
Бренд: Gantner Страницы: 4
AAT Holding KaDe KDH-KZ620U Installation Manual preview
KaDe KDH-KZ620U
Бренд: AAT Holding Страницы: 28
LAMBERTI ELEKTRONIK Latherm HZR Comfort Operating Manual preview
Latherm HZR Comfort
Бренд: LAMBERTI ELEKTRONIK Страницы: 16
3M Touch Screen Controller SX112 Reference Manual preview
Touch Screen Controller SX112
Бренд: 3M Страницы: 33
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Бренд: Davey Страницы: 8
ICP DAS USA CAN-8124 User Manual preview
CAN-8124
Бренд: ICP DAS USA Страницы: 153
VAL VLC-2430-4 Operation Manual preview
VLC-2430-4
Бренд: VAL Страницы: 10
Zonet ZUC2401 Quick Installation Manual preview
ZUC2401
Бренд: Zonet Страницы: 2
W8ZR StationPro II Operating Manual preview
StationPro II
Бренд: W8ZR Страницы: 77

Бренды по названию

Популярные бренды

Загрузить еще бренды