manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Crossbar Switch (XBAR)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

7-11

 

As an example of arbitration in round-robin mode, assume the three masters have ID’s 0, 1, and 2. If the 
last master of the slave port was master 1, and masters 0 and 2 make simultaneous requests, they are 
serviced in the order 2 and then 0 assuming no further requests are made.

As another example, if master 1 is waiting on a response from a slow slave and has no further pending 
access to that slave, no other masters are requesting, and master 0 then makes a request, master 0’s request 
is granted on the next clock (assuming that master 1’s transfer is not a burst transfer), and the request 
information for master 0 is driven to the slave as a pending access. If master 2 were to make a request after 
master 0 has been granted access, but prior to master 0’s access being accepted by the slave, master 0 
maintains the grant on the slave port, and master 2 is delayed until the next arbitration boundary, which 
occurs after the transfer is complete. The round-robin pointer is reset to 0, so if master 1 has another request 
that occurs before master 0’s transfer completes, master 1 is the granted the bus. This implies a worst case 
latency of 

N

 transfers for a system with 

N

 masters.

Parking may continue to be used in round-robin mode, but affects the round-robin pointer unless the 
parked master actually performs a transfer. Handoff to the next master in line occurs after one cycle of 
arbitration.

The slave port does an arbitration check at every clock edge to ensure that the proper master (if any) has 
control of the slave port.

A new requesting master must wait until the end of the fixed-length burst transfer, before it is granted 
control of the slave port. If the new requesting master’s priority level is lower than that of the master that 
currently has control of the slave port, the new requesting master is forced to wait until the master that 
currently has control of the slave port completes its access. 

7.3.6.2.1

Parking

If no master is currently requesting the slave port, the slave port is parked. The slave port parks in one of 
three places, indicated by the value of the PCTL field in the XBAR_SGPCR.

•

If park-on-specific master mode is selected, the slave port parks on the master designated by the 
PARK field. When the master accesses the slave port again, a one clock arbitration penalty is 
incurred only for an access request made by another master port to the slave port. No other 
arbitration penalties are incurred. All other masters pay a one clock penalty. 

•

If park-on-last (POL) mode is selected, then the slave port parks on the last master to access it, 
passing that master’s signals through to the slave bus. When the master accesses the slave port 
again, no other arbitration penalties are incurred except that a one clock arbitration penalty is 
incurred for each access request to the slave port made by another master port. All other masters 
pay a one clock penalty.

•

If the low-power-park (LPP) mode is selected, then the slave port enters low-power park mode. It 
is not under control by any master and does not transmit any master signals to the slave bus. All 
slave bus activity halts because all slave bus signals are not toggling. This saves power if the slave 
port is not used for some time. However, when a master does make a request to a slave port parked 
in low-power-park, a one clock arbitration delay is incurred to get ownership of the slave port.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

J4C 20 Mounting Instructions preview
20
Бренд: J4C Страницы: 4
Bartlett 3K Operation Manual preview
3K
Бренд: Bartlett Страницы: 7
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Бренд: Procom Страницы: 10
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Бренд: Invertek Страницы: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Бренд: Techtrol Страницы: 4
Shimaden PAC18A Series Instruction Manual preview
PAC18A Series
Бренд: Shimaden Страницы: 32
Samson 2371-10 Mounting And Operating Instructions preview
2371-10
Бренд: Samson Страницы: 36
Xvent ELEMENTAIR B-MARK I Operation And Installation Instructions Manual preview
ELEMENTAIR B-MARK I
Бренд: Xvent Страницы: 9
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Бренд: Continental Instruments Страницы: 2
Inner Range CONCEPT IQ User Manual preview
CONCEPT IQ
Бренд: Inner Range Страницы: 28
Ledj STAR11 User Manual preview
STAR11
Бренд: Ledj Страницы: 12
Parker Porter MPC Series Installation, Programming, & User Manual preview
Porter MPC Series
Бренд: Parker Страницы: 30
PPA Citrox CX-4512 Instruction Manual preview
Citrox CX-4512
Бренд: PPA Страницы: 2
Flowserve Limitorque QX Maintenance And Spare Parts preview
Limitorque QX
Бренд: Flowserve Страницы: 82
EPOS EPOS2 50/5 Application Note preview
EPOS2 50/5
Бренд: EPOS Страницы: 21
Ingersoll-Rand ZGB015-KIT Assembly preview
ZGB015-KIT
Бренд: Ingersoll-Rand Страницы: 5
Belden Miranda NV915 Quick Start Manual preview
Miranda NV915
Бренд: Belden Страницы: 4
TAC GUITAR MANIA Usage Instructions preview
GUITAR MANIA
Бренд: TAC Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды