Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 640 | Manualshive

Страница: 640 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-63

shows the timing for the A1 and B1 loading. A1 and B1 use the same signal to trigger a load,

which is generated based on the selected counter reaching one. This event is defined as the cycle boundary.
The load signal pulse has the duration of one system clock cycle and occurs at the first system clock period
of every cycle of the counter. If A2 and B2 are written within cycle (

n

), their values are loaded into A1 and

B1, respectively, at the first clock of cycle (

n

+1). The update disable bits, EMIOS_OUDR, can be used to

control the update of these registers, thus allowing the delay of A1 and B1 update for synchronization
purposes.

During the load pulse A1 still holds its old value, which is updated on the following system clock cycle.
During the A1 load pulse, an internal by-pass allows the use of A2 instead of A1 for matches if A2 is either
0 or 1, thus allowing matches to be generated even when A1 is being loaded. This approach allows a
uniform channel operation for any A2 value, including 1 and 0.

it is assumed that the channel and global prescalers are set to one, meaning that the channel

internal counter transition at every system clock cycle. FLAGs can be generated only on B1 matches when
MODE[5] is cleared, or on both A1 and B1 matches when MODE[5] is set. Since B1 FLAG occurs at the
cycle boundary, this flag can be used to indicate that A2 or B2 data written on cycle (

n

) were loaded to A1

or B1, respectively, thus generating matches in cycle (

n

+1).

Figure 16-46. eMIOS OPWFMB Mode Example — A1/B1 Updates and Flags

Cycle n

Cycle n+1

Cycle n+2

A1 value

B1 value

B2 value

0x000008

0x000002

0x000006

0x000008

0x000001

EMIOS_CCNTR

n

0x000004

0x000006

MODE[0] = 1

A2 value

0x000002 0x000004

0x000006

0x000002

0x000004

0x000006

0x000008

0x000006

Output flip-flop

Write to B2

Match A1

Match B1

Match B1

A1/B1 load signal

Due to B1 match

FLAG set event

cycle n-1

Time

Write to A2

Match A1

Write to A2

Match B1

EDPOL = 0

«
...
638
639
640
641
642
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Wasp Страницы: 16

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 23

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: EBS Страницы: 116

Бренд: Daikin Страницы: 2

GreenMax DRC DRC07-ED0

Бренд: Leviton Страницы: 2

Бренд: Freescale Semiconductor Страницы: 34

Бренд: Matelec Страницы: 2

Бренд: V2 Страницы: 108

Бренд: Powtran Страницы: 40

Бренд: Jung Страницы: 8

xComfort CJAU-01 Series

Бренд: Eaton Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды