Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 682 | Manualshive

Страница: 682 / 1153

background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

17-27

5

Reserved.

6

AM

Angle mode selection. When the AM bit is set, the EAC (eTPU Angle Clock) hardware provides angle
information to the channels using the TCR2 bus. When the AM bit is cleared (non-angle mode), EAC
operation is disabled, and its internal registers can be used as general purpose registers.
0 EAC operation is disabled.
1 TCR2 works in angle mode;

Note:

AM must not be changed when ETPU_MCR[GTBE] = 1.

Note:

Changing AM can cause expurious transition detections on channel 0, depending on the channel

mode and state.

For more information, refer to the

eTPU Reference Manual

.

7–9

Reserved.

10–15

TCR2P

Timer count register 2 prescaler control. Part of the TCR2 clocking system. TCR2 is clocked from the output
of a prescaler. The prescaler divides its input by (TCR2P+1) allowing frequency divisions from 1 to 64. The
prescaler input is the system clock divided by 8 (in gated or non-gated clock mode) or Internal Timebase
input, or TCRCLK filtered input. This field has no effect on TCCR2 in Angle Mode. For more information on
TCR2, refer to the

eTPU Reference Manual

.

16–23

TCR1CTL

TCR1 clock/gate control. Part of the TCR1 clocking system. It determines the clock source for TCR1. TCR1
can count on detected rising edge of the TCRCLK signal or the system clock divided by 2. After reset
TCRCLK signal is selected. The following table shows the selection of the TCR1 clock source.

For more information on the TCR1 clocking system, refer to the

eTPU Reference Manual

.

24–31

TCR1P

Timer count register 1 prescaler control. Clocked from the output of a prescaler. The input to the prescaler is
the internal eTPU system clock divided by 2 or the output of TCRCLK filter, or Peripheral Timebase input.
The prescaler divides this input by (TCR1P+1) allowing frequency divisions from 1 up to 256.

Table 17-11. ETPU_TBCR Field Descriptions (continued)

Field

Description

TCR1CTL

TCR1 Clock

00

selects TCRCLK as clock source for the TCR1 prescaler (must not be use
in Angle Mode)

01

Reserved

10

selects system clock divided by 2 as clock source for the TCR1 prescaler

11

TCR1CTL shuts down TCR1 clock. TCR1 can still change if STAC client.

«
...
680
681
682
683
684
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: UE Страницы: 4

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: Madison AV Страницы: 2

Бренд: Trane Technologies Страницы: 8

Бренд: Lampert Страницы: 15

Бренд: Cardin Elettronica Страницы: 56

Бренд: Atmel Страницы: 12

Бренд: NDS Страницы: 20

Бренд: PPI Страницы: 27

Бренд: Niko Страницы: 80

Бренд: PacComm Страницы: 29

Бренд: Belimo Страницы: 10

Wireless Meter Scanner & Controller wi...

Бренд: Omega Engineering Страницы: 96

Бренд: MPS Страницы: 12

LandStar GPLI Series

Бренд: Epever Страницы: 2

Бренд: Rain Deck Страницы: 2

Бренд: Motorline Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды