manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-41

 

24.11.3 Read/Write Access Control/Status (RWCS)

The read write access control/status register provides control for read/write access. Read/write access 
provides DMA-like access to memory-mapped resources on the system bus either while the processor is 
halted, or during runtime. The RWCS register also provides read/write access status information as shown 
in 

Table 24-30

.

Nexus Reg: 0x0007

Access: R/W

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

AC

RW

SZ

MAP

PR

BST

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

 

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

CNT

ERR

DV

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 24-18. Read/Write Access Control/Status Register (RWCS)

Table 24-29. RWCS Field Description

Field

Description

31

AC

Access control.
0 End access
1 Start  access

30

RW

Read/write select.
0 Read access
1 Write access

29–27

SZ[2:0]

Word size.
000 8-bit (byte)
001 6-bit (halfword)
010 32-bit (word)
011 64-bit (doubleword - only in burst mode)
100–111 Reserved (default to word)

26–24

MAP[2:0]

MAP select.
000 Primary memory map
001-111 Reserved

23–22

PR[1:0]

Read/write access priority.
00 Lowest access priority
01 Reserved (default to lowest priority)
10 Reserved (default to lowest priority)
11 Highest access priority

21

BST

Burst control.
0 Module accesses are single bus cycle at a time.
1 Module accesses are performed as burst operation.

20–16

Reserved.

15–2

CNT[13:0]

Access control count. Number of accesses of word size SZ

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

GE RSTi-EP User Manual preview
RSTi-EP
Бренд: GE Страницы: 425
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
OLYS MPPT5010 User Manual preview
MPPT5010
Бренд: OLYS Страницы: 4
Watersports Innovations The Boost Box WS 1107 Installation & Operation Instructions preview
The Boost Box WS 1107
Бренд: Watersports Innovations Страницы: 12
Parker IQAN-XS2 Instruction Book preview
IQAN-XS2
Бренд: Parker Страницы: 31
Jetter JVM-104-O09 User Manual preview
JVM-104-O09
Бренд: Jetter Страницы: 62
TE Connectivity AMP 3K/40 CE 2161600-1 Original Instructions Manual preview
AMP 3K/40 CE 2161600-1
Бренд: TE Connectivity Страницы: 29
MAKOT UMS-04 Series Manual preview
UMS-04 Series
Бренд: MAKOT Страницы: 6
Eaton Jockey XTJP O & M Manual preview
Jockey XTJP
Бренд: Eaton Страницы: 12
NELSEN WATER NRO ROC2 Documentation preview
NRO ROC2
Бренд: NELSEN WATER Страницы: 16
Galil Motion Control DMC-14 5 Series Manual preview
DMC-14 5 Series
Бренд: Galil Motion Control Страницы: 200
AGS Merlin 1000SW+ Installation Operation & Maintenance preview
Merlin 1000SW+
Бренд: AGS Страницы: 12
BWT PLATINE DE SPA SP800 Installation Instructions Manual preview
PLATINE DE SPA SP800
Бренд: BWT Страницы: 48
Drawmer CMC2 Manual preview
CMC2
Бренд: Drawmer Страницы: 16
Dorset Trovan Access Guard Installation Manual preview
Trovan Access Guard
Бренд: Dorset Страницы: 15
Magnetek IMPULSE G+ Series 3 Instruction Manual preview
IMPULSE G+ Series 3
Бренд: Magnetek Страницы: 9
Carrier WSHP Open v3 Integration Manual preview
WSHP Open v3
Бренд: Carrier Страницы: 58
Full Gauge Controls MT-514e Manual preview
MT-514e
Бренд: Full Gauge Controls Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды