Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1059 | Manualshive

Страница: 1059 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-66

Freescale Semiconductor

Error information is messaged out in the following format (refer to

):

Figure 24-51. Error Message Format

24.11.14.4 Watchpoint Timing Diagram (2 MDO and 1 MSEO Configuration)

Figure 24-52. Watchpoint Message and Watchpoint Error Message

24.11.15 NZ6C3 Read/Write Access to Memory-Mapped Resources

The read/write access feature allows access to memory-mapped resources via the JTAG/OnCE port. The
read/write mechanism supports single as well as block reads and writes to e200z6 system bus resources.

The NZ6C3 module is capable of accessing resources on the e200z6 system bus, with multiple
configurable priority levels. Memory-mapped registers and other non-cached memory can be accessed via
the standard memory map settings.

All accesses are setup and initiated by the read/write access control/status register (RWCS), as well as the
read/write access address (RWA) and read/write access data registers (RWD).

Using the read/write access registers (RWCS/RWA/RWD), memory-mapped e200z6 system bus resources
can be accessed through NZ6C3. The following subsections describe the steps which are required to access
memory-mapped resources.

NOTE

Read/write access can only access memory mapped resources when system
reset is de-asserted.

Misaligned accesses are NOT supported in the e200z6 Nexus3 module.

ECODE (00110 / 01000)

MSB

LSB

1

2

SRC

TCODE (001000)

3

6 bits

4 bits

5 bits

Fixed length = 15 bits

WPM:

MCKO

MSEO

TCODE = 15
Source Processor = 0b00
Watchpoint Number = 2

MDO[1:0]

11

00

00

10

00

00

00

10

00

00

10

01

00

Error:
TCODE = 8
Source Processor = 0b00
Error Code = 6 (Queue Overrun – WPM Only)

Error

Watchpoint

11

«
...
1057
1058
1059
1060
1061
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Hanna Instruments Страницы: 88

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Viking Страницы: 4

Бренд: Ezodo Страницы: 7

Бренд: Frico Страницы: 8

Бренд: YASKAWA Страницы: 360

Бренд: Zero 88 Страницы: 34

Бренд: Sturtevant Richmont Страницы: 73

Бренд: C-TEC Страницы: 42

Бренд: Galcon Страницы: 24

freescale Kinetics TWR-K60N512-KEIL

Бренд: NXP Semiconductors Страницы: 5

Бренд: S2Tech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды