Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1053 | Manualshive

Страница: 1053 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-60

Freescale Semiconductor

NOTE

For the e200z6 based CPU, the doubleword encoding (data size

= 0b000)

will indicate a doubleword access and will be sent out as a single data trace
message with a single 64-bit data value.

24.11.13.2.3 DTM Overflow Error Messages

An error message occurs when a new message cannot be queued due to the message queue being full. The
FIFO will discard incoming messages until it has completely emptied the queue. After it is emptied, an
error message will be queued. The error encoding will indicate which types of messages attempted to be
queued while the FIFO was being emptied.

If only a data trace message attempts to enter the queue while it is being emptied, the error message will
incorporate the data trace only error encoding (00010). If both OTM and data trace messages attempt to
enter the queue, the error message will incorporate the OTM and data trace error encoding (00111). If a
watchpoint also attempts to be queued while the FIFO is being emptied, then the error message will
incorporate error encoding (01000).

NOTE

The OVC bits within the DC1 register can be set to delay the CPU to
alleviate (but not eliminate) potential overrun situations.

Error information is messaged out in the following format:

Figure 24-45. Error Message Format

24.11.13.2.4 Data Trace Synchronization Messages

A data trace write/read with sync. message is messaged via the auxiliary port (provided data trace is
enabled) for the following conditions (refer to

):

•

Initial data trace message after exit from system reset or whenever data trace is enabled

•

Upon exiting debug mode

•

After occurrence of queue overrun (can be caused by any trace message), provided data trace is
enabled

•

After the periodic data trace counter has expired indicating 255

without-sync

data trace messages

have occurred since the last

with-sync

message occurred

•

Upon assertion of the event in (EVTI) pin, the first data trace message will be a synchronization
message if the EIC bits of the DC1 register have enabled this feature

•

Upon data trace write/read after the previous DTM message was lost due to an attempted access to
a secure memory location

DATA

MSB

LSB

2

3

4

U-ADDR

DSZ

SRC

5

4 bits

1

TCODE (000110)

3 bits

1-32 bits

1-64 bits

6 bits

Max length = 109 bits; Min length = 15 bits

«
...
1051
1052
1053
1054
1055
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: eclisse Страницы: 40

Бренд: U-Prox Страницы: 25

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: Samson Страницы: 70

Бренд: Danfoss Страницы: 36

Бренд: Lumel Страницы: 32

Бренд: Zonex Страницы: 16

Бренд: rotork Страницы: 22

Бренд: FASTRON. Страницы: 37

Бренд: Festo Страницы: 2

Бренд: Aube Technologies Страницы: 12

Touchline PL 2 Ch

Бренд: Roth Страницы: 8

Бренд: Fego Precision Industrial Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды