Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 826 | Manualshive

Страница: 826 / 1153

background image

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

19-3

The DSPI has three configurations:

•

Serial peripheral interface (SPI) configuration where the DSPI operates as an SPI with support for
queues.

•

Deserial serial interface (DSI) configuration where the DSPI serializes eTPU and eMIOS output
channels and deserializes the received data by placing the data on the eTPU and eMIOS input
channels and as inputs to the external interrupt request submodule of the SIU.

•

Combined serial interface (CSI) configuration where the DSPI operates in both SPI and DSI
configurations interleaving DSI frames with SPI frames, giving priority to SPI frames.

For queued operations the SPI queues reside in internal SRAM which is external to the DSPI. Data
transfers between the queues and the DSPI FIFOs are accomplished through the use of the eDMA
controller or through host software.

shows a DSPI with external queues in internal SRAM.

Figure 19-2. DSPI with Queues and eDMA

19.1.3

Features

The DSPI supports these SPI features:

•

Full-duplex, three-wire synchronous transfers

•

Master and slave mode

•

Buffered transmit and receive operation using the TX and RX FIFOs, with depths of four entries

•

Visibility into TX and RX FIFOs for ease of debugging

•

FIFO bypass mode for low-latency updates to SPI queues

Internal SRAM

TX queue

RX queue

Address/control

TX FIFO

DSPI

RX FIFO

RX data

TX data

TX data

RX data

Shift register

eDMA controller

Address/control

or host CPU

«
...
824
825
826
827
828
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: S&C Страницы: 40

Бренд: Eaton Страницы: 16

Бренд: NAVITAS Страницы: 7

Бренд: Vexve Страницы: 24

Бренд: Nibe Страницы: 20

STM32F469 Series

Бренд: ST Страницы: 31

Бренд: V2 Страницы: 60

Бренд: ENGGA Страницы: 8

CYPRESS Traveo S6J335 Series

Бренд: Infineon Technologies Страницы: 308

Бренд: VECTOR CONTROLS Страницы: 10

Бренд: AMX Страницы: 2

ACT4910EVK1-121

Бренд: Active-semi Страницы: 15

DMX LED EASY Operator Deluxe

Бренд: EuroLite Страницы: 16

Intelligent Power Controller 3000

Бренд: Eaton Страницы: 2

Thermal Entry Wizard

Бренд: ATN Страницы: 56

Бренд: PROEL Страницы: 34

ProCon D400 Series

Бренд: ICON Страницы: 28

Бренд: National Instruments Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды