manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

13-29

 

13.4.2.3.1

Software Locking

A software mechanism is provided to independently lock/unlock each high, mid, and low address space 
against program and erase.

Software Locking is done through the FLASH_LMLR (low/mid address space block locking register), 
FLASH_SLMLR (secondary low/mid address space block locking register), or FLASH_HLR (high 
address space block locking register). These can be written through register writes, and can be read through 
register reads.

When the program/erase operations are enabled through hardware, software locks are enforced through 
doing register writes.

13.4.2.3.2

Flash

 

Program Suspend/Resume

The program sequence can be suspended to allow read access to the flash core. It is not possible to erase 
or program during a program suspend. Do not attempt interlock writes during program suspend.

A program suspend can be initiated by changing the value of the FLASH_MCR[PSUS] bit from a 0 to a 
1. FLASH_MCR[PSUS] can be set high at any time when FLASH_MCR[PGM] and 
FLASH_MCR[EHV] are high. A 0 to 1 transition of FLASH_MCR[PSUS] causes the flash module to start 
the sequence to enter program suspend, which is a read state. The module is not suspended until 
FLASH_MCR[DONE] = 1. At this time, flash core reads can be attempted. After it is suspended, the flash 
core can only be read. Reads to the blocks being programmed/erased return indeterminate data.

The program sequence is resumed by writing a logic 0 to FLASH_MCR[PSUS]. FLASH_MCR[EHV] 
must be set to a 1 before clearing FLASH_MCR[PSUS] to resume operation. When the operation resumes, 
the flash module continues the program sequence from one of a set of predefined points. This can extend 
the time required for the program operation.

13.4.2.4

Flash

 

Erase

Erase changes the value stored in all bits of the selected blocks to logic 1. Locked or disabled blocks cannot 
be erased. If multiple blocks are selected for erase during an erase sequence, the blocks are erased 
sequentially starting with the lowest numbered block and terminating with the highest. Aborting an erase 
operation leaves the flash core blocks being erased in an indeterminate data state. This can be recovered 
by executing an erase on the affected blocks.

The erase sequence consists of the following sequence of events: 

1. Change the value in the FLASH_MCR[ERS] bit from 0 to a 1.

2. Select the block, or blocks to be erased by writing ones to the appropriate registers in 

FLASH_LMSR or FLASH_HSR. If the shadow row is to be erased, this step can be skipped, and 
FLASH_LMSR and FLASH_HSR are ignored. For shadow row erase, refer to section 

Section 13.4.2.5, “Flash Shadow Block

” for more information.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Harsco Industrial ENVI Advanced User'S Manual preview
ENVI
Бренд: Harsco Industrial Страницы: 57
µ-Dimension D3208 User Manual preview
D3208
Бренд: µ-Dimension Страницы: 48
µ-Dimension D4006 Installation Instructions preview
D4006
Бренд: µ-Dimension Страницы: 2
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Бренд: SDC Страницы: 6
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Бренд: Mold-Masters Страницы: 2
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Бренд: Trinamic Страницы: 30
Pangolin FB4 Series User Manual preview
FB4 Series
Бренд: Pangolin Страницы: 35
Infineon XE166 Series Hardware Manual preview
XE166 Series
Бренд: Infineon Страницы: 28
R-Tec controlR Installation Manual & User Manual preview
controlR
Бренд: R-Tec Страницы: 14
Current Mini LOOP BT Quick Start Manual preview
Mini LOOP BT
Бренд: Current Страницы: 4
PEAS VC-530E User Manual preview
VC-530E
Бренд: PEAS Страницы: 4
Sollae Systems CIE-M10A User Manual preview
CIE-M10A
Бренд: Sollae Systems Страницы: 72
QSC TSC-101-G3 User Manual preview
TSC-101-G3
Бренд: QSC Страницы: 13
GCE Druva MTLX Instructions For Use Manual preview
Druva MTLX
Бренд: GCE Страницы: 46
Tusa RS-790 Owner'S Manual preview
RS-790
Бренд: Tusa Страницы: 72
Danfoss 080Z0130 Manual preview
080Z0130
Бренд: Danfoss Страницы: 96
Matrix COSEC PANEL200 Quick Start Manual preview
COSEC PANEL200
Бренд: Matrix Страницы: 10
Samson TROVIS 5724-8 Mounting And Operating Instructions preview
TROVIS 5724-8
Бренд: Samson Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды