Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 1153

background image

e200z6 Core Complex

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

3-19

3.3.1.5.3

MAS[2] Register

The MAS[2] register is shown in

.

MAS[2] fields are defined in

SPR: 626

Access: R/W

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

R

EPN

—

V

L

E

W

I

M G E

W

Reset

Undefined on Power Up

⎯

Unchanged on Reset

Figure 3-9. MMU Assist Register 2 — MAS[2]

Table 3-5. MAS[2] — EPN and Page Attributes

Field

Description

0–19

EPN

Effective page number [0:19].

20–25

Reserved, must be cleared.

26

VLE

Power Architecture VLE.
0 This page is a standard Book E page.
1 This page is a Power Architecture VLE page.

27

W

Write-through required.
0 This page is considered write-back with respect to the caches in the system.
1 All stores performed to this page are written through to main memory.

28

I

Cache inhibited.
0 This page is considered cacheable.
1 This page is considered cache-inhibited.

29

M

Memory coherence required.The e200z6 does not support the memory coherence required attribute, and thus it is
ignored.
0 Memory coherence is not required.
1 Memory coherence is required.

30

G

Guarded. The e200z6 ignores the guarded attribute because no speculative or out-of-order processing is performed.
0 Access to this page are not guarded, and can be performed before it is known if they are required by the sequential

execution model.

1 All loads and stores to this page are performed without speculation (that is, they are known to be required).

31

E

Endianness. Determines endianness for the corresponding page.
0 The page is accessed in big-endian byte order.
1 The page is accessed in true little-endian byte order.

«
...
124
125
126
127
128
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Hanbay Страницы: 18

Бренд: Federal Signal Corporation Страницы: 34

Бренд: Gardner Denver Страницы: 22

Бренд: YOKOGAWA Страницы: 150

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

DIGITAL EPIC-2 DTM

Бренд: Westlock Страницы: 33

Бренд: Qorvo Страницы: 6

Бренд: Danfoss Страницы: 6

RailBoss 4 Basic

Бренд: G-Scale Graphics Страницы: 22

Бренд: Interactive Technologies Страницы: 431

Бренд: Walchem Страницы: 35

Бренд: AL-KO Страницы: 52

Бренд: Belimo Страницы: 4

AGCO RoGator Hawkeye C Series

Бренд: Raven Страницы: 64

Бренд: AudioCodes Страницы: 10

Бренд: Gira Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды