Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 575 | Manualshive

Страница: 575 / 1153

background image

Boot Assist Module (BAM)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

15-16

Freescale Semiconductor

NOTE

Internal SRAM is protected by 64-bit wide error correction coding hardware
(ECC). All writes to uninitialized internal SRAM must be 64 bits wide, or
an ECC error occurs. The BAM buffers download data until 8-bytes are
received, and then executes a single 64-bit wide write. Only internal SRAM
supports 64-bit writes. Downloading data to RAM other than internal
SRAM causes errors.

If the start address of the downloaded data is not on an 8-byte boundary, the
BAM writes 0x00 beginning at the preceding 8-byte boundary memory
location to the start address (4 byte maximum). The BAM also writes 0x00
to all memory locations from the last data byte downloaded to the following
8-byte boundary (7 byte maximum).

4. Execute the code.

The BAM waits for the last eSCI message transmission to complete and then disables the eSCI.
TXDA and RXDA revert to general-purpose inputs. The BAM branches to the starting address
where the downloaded code is stored (specified in step 2) and executes the code.

NOTE

The code that downloads and executes must periodically refresh the e200z6
watchdog timer or change the timeout period to a value that does not cause
resets during normal operation.

15.3.3

Interrupts

No interrupts are generated or enabled by the BAM.

Table 15-11. eSCI Serial Boot Mode Download Process

Step

Host Sent Message

BAM Response

Message

Action

1

64-bit password MSB first

64-bit password

Password checked for validity and compared against
stored password. e200z6 watchdog timer is
refreshed if the password check is successful

2

32-bit store a
32-bit number of bytes
MSB first

32-bit store address
+ 32-bit number of bytes

Load address and size of download are stored for
future use

3

8 bits of raw binary data

8 bits of raw binary data Each byte of data received is stored in MCU

memory, starting at the address specified in the
previous step and incrementing until the number of
data bytes received and stored matches the number
of data bytes specified in the preceding step.

4

None

None

The BAM returns I/O pins and the eSCI module to
their reset state, except it asserts
ESCI_A_CR2[MDIS] instead of negates. Then the
BAM branches to the starting address of the stored
data specified in step 2.

«
...
573
574
575
576
577
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Bartec Страницы: 26

Бренд: Danfoss Страницы: 37

Бренд: xpr Страницы: 4

Бренд: Teledyne Страницы: 102

Бренд: DH Instruments Страницы: 30

BMS NUV100-CI-12

Бренд: Nuvation Страницы: 41

Бренд: National Instruments Страницы: 100

Бренд: Gardenic Страницы: 14

RailBoss 4 Basic

Бренд: G-Scale Graphics Страницы: 22

Бренд: Interactive Technologies Страницы: 431

Бренд: Viking Electronics Страницы: 12

Бренд: AMD Страницы: 12

MC DC-2.00 Series

Бренд: Hanbay Страницы: 7

HIMatrix F31 02

Бренд: HIMA Страницы: 48

Бренд: Salus Страницы: 40

Бренд: Jabra Страницы: 13

Бренд: Altronix Страницы: 20

Бренд: DeZurik Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды