Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 774 | Manualshive

Страница: 774 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

18-75

18.4.3.6.2

Command Queue Completion Status

The end of queue flag, EQADC_FISRn[EOQF] (see

Section 18.3.2.8, “eQADC FIFO and Interrupt Status

Registers 0–5 (EQADC_FISRn)

”) is asserted when the eQADC completes the transfer of a CFIFO entry

with an asserted EOQ bit. Software sets the EOQ bit in the last command message of a user-defined
command queue to indicate that this entry is the end of the queue. Refer to

Section 18.4.1.2, “Message

Format in eQADC

,” for information on command message formats. The transfer of entries bound for the

on-chip ADCs is considered completed when they are stored in the appropriate command buffer. The
transfer of entries bound for the external device is considered completed when the serial transmission of
the entry is completed.

The command with a EOQ bit asserted is valid and is transferred. When EQADC_CFCRn[EOQIE] (refer
to

Section 18.3.2.6, “eQADC CFIFO Control Registers 0–5 (EQADC_CFCRn)

EQADC_FISRn[EOQF] are asserted, the eQADC generates an end of queue interrupt request.

7

TRIGGERED

(11)

IDLE

(0b00)

• CFIFO in single-scan mode, eQADC detects the EOQ bit

asserted at end of command transfer, and CFIFO mode is
not modified to disabled, OR

• CFIFO, in single-scan level trigger mode, and the gate

closes while no commands are being transferred from the
CFIFO, and CFIFO mode is not modified to disabled, OR

• CFIFO, in single-scan level trigger mode, and eQADC

detects a closed gated at end of command transfer, and
CFIFO mode is not modified to disabled, OR

• CFIFO mode is modified to disabled mode and CFIFO was

not transferring commands.

• CFIFO mode is modified to disabled mode while CFIFO was

transferring commands, and CFIFO completes or aborts the
transfer.

8

WAITING FOR

TRIGGER

(0b10)

• CFIFO in single or continuous-scan edge trigger mode,

eQADC detects the pause bit asserted at the end of
command transfer, the EOQ bit in the same command is
negated, and CFIFO mode is not modified to disabled, OR

• CFIFO in continuous-scan edge trigger mode, eQADC

detects the EOQ bit asserted at the end of command
transfer, and CFIFO mode is not modified to disabled, OR

• CFIFO, in continuous-scan level trigger mode, and the gate

closes while no commands are being transferred from the
CFIFO, and CFIFO mode is not modified to disabled, OR

• CFIFO, in continuous-scan level trigger mode, and eQADC

detects a closed gated at end of command transfer, and
CFIFO mode is not modified to disabled.

9

TRIGGERED

(0b11)

• No event to switch to IDLE or WAITING FOR TRIGGER

status has happened.

Table 18-45. Command FIFO Status Switching Condition (continued)

No.

From Current
CFIFO Status

(CFS)

To New CFIFO

Status (CFS)

Status Switching Condition

«
...
772
773
774
775
776
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: Therma-Stor Страницы: 20

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

ELEMENTAIR B-MARK I

Бренд: Xvent Страницы: 9

Dynamic Boiler Controller

Бренд: Intiel Страницы: 25

Бренд: Parker Страницы: 24

Бренд: HomeMatic Страницы: 38

Бренд: MSA Страницы: 309

EscapeKeeper JR

Бренд: Fright Ideas Страницы: 2

Бренд: Ledj Страницы: 12

Бренд: Danfoss Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды