manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

17-41

17.4.6.3

eTPU Channel 

n

 Status Control Register (ETPU_C

n

SCR)

ETPU_C

n

SCR is a collection of the interrupt status bits of the channel, and also the function mode 

definition (read-write). Bits CIS, CIOS, DTRS, and DTROS for each channel can also be accessed from 
ETPU_CISR, ETPU_CIOSR, ETPU_CDTRSR, and ETPU_CDTROSR respectively. For more 
information on the three previously mentioned registers, refer to the 

eTPU Reference Manual

.

NOTE

The device core must write 1 to clear a status bit.

NOTE

In the MPC5565, eTPU A channels [0:2, 14:15] are DMA connected. The 
data transfer request lines that are not connected to the DMA controller are 
left disconnected and do not generate transfer requests, even if their request 
status bits assert in registers ETPU_CDTRSR and ETPU_C

n

SCR

18–20

Reserved.

21–31
CPBA

[0:10]

Channel 

n

 parameter base address. The value of this field multiplied by 8 specifies the SDM parameter base host 

(byte) address for channel 

n

 (2-parameter granularity).

The formula for calculating the absolute channel parameter base (byte) address, as seen by the host, is eTPU_Base 
+  CPBA*8. The SDM is mirrored in the parameter sign extension (PSE) area. The formula to calculate the 
absolute channel parameter base (byte) address in the PSE area is eTP CPBA*8.
For more information on SDM addresses, refer to the 

eTPU Reference Manual

.

Address: Channel_Registe 0x0004

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

CIS

CIOS

0

0

0

0

0

0

DTRS DTROS

0

0

0

0

0

0

W

w1c

w1c

w1c

w1c

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

IPS

OPS

0

0

0

0

0

0

0

0

0

0

0

0

FM

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 17-23. eTPU Channel 

n

 Status Control Register (ETPU_C

n

SCR)

Table 17-25.  ETPU_C

n

CR Field Descriptions (continued)

Field

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

H3C WX5500H series User Configuration Manual preview
WX5500H series
Бренд: H3C Страницы: 57
EasyIO FG Series User Manual preview
FG Series
Бренд: EasyIO Страницы: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Бренд: RMG Страницы: 6
Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Бренд: Campbell Страницы: 8
Gamma Vacuum SPCe User Manual preview
SPCe
Бренд: Gamma Vacuum Страницы: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Бренд: Gamma Страницы: 28
Harman Kardon OMNI 10 Quick Start Manual preview
OMNI 10
Бренд: Harman Kardon Страницы: 25
Uniss SR601 Operation Instructions Manual preview
SR601
Бренд: Uniss Страницы: 21
Partizan PAB-FC2 Quick Start Manual preview
PAB-FC2
Бренд: Partizan Страницы: 7
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Бренд: ICP DAS USA Страницы: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Бренд: National Instruments Страницы: 22
Rheem RXMD-B04 Installation Instructions preview
RXMD-B04
Бренд: Rheem Страницы: 2
OMEGA AIR AWS-C Instructions Manual preview
AWS-C
Бренд: OMEGA AIR Страницы: 12
Jordan Valve Mark 60 Series Installation & Maintenance Instructions preview
Mark 60 Series
Бренд: Jordan Valve Страницы: 5
Suzhou Lily ZL-7901A Instruction Manual preview
ZL-7901A
Бренд: Suzhou Lily Страницы: 8
Native Instruments komplete kontrol s series Manual preview
komplete kontrol s series
Бренд: Native Instruments Страницы: 338
Samson Trovis 6493 Mounting And Operating Instructions preview
Trovis 6493
Бренд: Samson Страницы: 128
Bose FREESPACE 4400 Service Manual preview
FREESPACE 4400
Бренд: Bose Страницы: 107

Бренды по названию

Популярные бренды

Загрузить еще бренды