manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Introduction

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

1-15

 

processor, and for a write operation, the data from the processor is written to cache. If the access does not 
match a valid cache tag entry (misses in the cache), or a write access is required to memory, the cache 
performs a bus cycle on the system bus. 

1.4.12

Static RAM (SRAM)

The MPC5500 family internal SRAM module provides a general-purpose memory block that supports 
mapped read/write accesses from any master. The SRAM size is 80 KB. Included within the SRAM block 
is a 32-KB block powered by a separate supply for standby operation and ECC error correction and 
detection.

1.4.13

Boot Assist Module (BAM)

The boot assist module (BAM) is read-only memory programmed by Freescale and is identical for all 
MCUs with an e200z6 core. The BAM program executes every time the MCU is powered on, or when 
reset in normal mode. The BAM supports theseboot modes:

•

Booting from internal flash memory 

•

Single master booting from external memory

•

Serial boot loading (program is downloaded to SRAM over an eSCI or FlexCAN peripheral and 
then executed)

The BAM reads the reset configuration halfword (RCHW) from flash memory (either internal or external) 
to configure the device hardware. The MMU is then configured for all resources and maps all physical 
addresses to logical addresses with the minimum address translation, to allow application boot code to 
execute as either Classic Power Architecture Book E code (default) or as Freescale VLE code. 

1.4.14

Enhanced Management Input/Output System (eMIOS)

The enhanced modular I/O system (eMIOS) module generates or measures time events. A unified channel 
(UC) module provides a consistent interface to a superset of all the MIOS channel functionality. This 
allows more flexibility to program each unified channel for different functions in different applications. 
To identify up to two timed events, each UC uses two comparators, a time base selector, and registers. This 
structure can produce match events to measure or generate a waveform. Alternatively, input events can 
capture the time base, allowing measurement of an input signal.

1.4.15

Enhanced Time Processing Unit (eTPU)

The enhanced time processing unit (eTPU) is an enhanced coprocessor designed for timing control. 
Operating in parallel with the host CPU, the eTPU processes instructions and real-time input events, 
performs output waveform generation, and accesses shared data without host intervention. Consequently, 
for each timer event, the CPU setup and service times are minimized or eliminated. In the MCU, the TPU 
engine is combined with shared instruction and data RAM to form a powerful time processing subsystem. 

The MPC5565 has one eTPU engine. High-level assembler/compiler and documentation can be used to 
develop customized functions for the eTPU. The eTPU supports several features of older TPU versions, 
making it easy to port older applications.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Particle B Series Quick Start Manual preview
B Series
Бренд: Particle Страницы: 6
ADEMCO MAX Programming Instructions preview
MAX
Бренд: ADEMCO Страницы: 2
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Бренд: Zener Страницы: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Бренд: Zapi Страницы: 5
EasyIO FG-20 Installation Manual preview
FG-20
Бренд: EasyIO Страницы: 17
Comeval Diaval AF Series Installation, Operating And Maintenance Manual preview
Diaval AF Series
Бренд: Comeval Страницы: 10
TAC Xenta 102 Handbook preview
Xenta 102
Бренд: TAC Страницы: 76
R-Tec controlR Installation Manual & User Manual preview
controlR
Бренд: R-Tec Страницы: 14
Xylem Goulds ResiBoost RB111512 Instruction Manual preview
Goulds ResiBoost RB111512
Бренд: Xylem Страницы: 40
WAREMA LONMPM 8DI Operating And Installation Instructions preview
LONMPM 8DI
Бренд: WAREMA Страницы: 4
MRC TECH 6 0001203 Quick Start Manual preview
TECH 6 0001203
Бренд: MRC Страницы: 2
CS Technologies ACE-CONVERTER Installation Manual preview
ACE-CONVERTER
Бренд: CS Technologies Страницы: 4
Abelko UltraBase20 User Manual preview
UltraBase20
Бренд: Abelko Страницы: 70
BIFFI ALGAS-MHP Installation, Operation And Maintenance Manual preview
ALGAS-MHP
Бренд: BIFFI Страницы: 56
Zennio MINiBOX 0-10V X1 User Manual preview
MINiBOX 0-10V X1
Бренд: Zennio Страницы: 25
Proton ECOMATIC PRO ECP 220 Operation Manual preview
ECOMATIC PRO ECP 220
Бренд: Proton Страницы: 36
Toho Electronics TTM-00BW Operation Manual preview
TTM-00BW
Бренд: Toho Electronics Страницы: 37
Arroyo Instruments ComboPak 685 Series User Manual preview
ComboPak 685 Series
Бренд: Arroyo Instruments Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды