Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 1153

background image

Introduction

MPC5565 Microcontroller Reference Manual, Rev. 1.0

1-4

Freescale Semiconductor

– Supports tag and data parity

— Vectored interrupt support

— Interrupt latency is less than 70 ns @132 MHz (measured from interrupt request to execution

of first instruction of interrupt exception handler)

— Reservation instructions for implementing read-modify-write constructs

(internal SRAM and flash)

— Signal processing engine (SPE) auxiliary processing unit (APU) operating on 64-bit GPRs

— Floating point

– IEEE

®

754 compatible with software wrapper

– Single precision in hardware, double precision with software library

– Conversion instructions between single precision floating point and fixed point

— Long cycle time instructions, except for guarded loads, do not increase interrupt latency in the

MPC5565; to reduce latency, long cycle time instructions are aborted upon interrupt requests

— Extensive system development support through Nexus debug module

•

System bus crossbar switch (XBAR)

— Three master ports, five slave ports.

— 32-bit address bus, 64-bit data bus

— Simultaneous accesses from different masters to different slaves (there is no clock penalty

when a parked master accesses a slave)

•

Enhanced direct memory access (eDMA) controller

— 32 channels support independent 8-, 16-, 32-bit single value or block transfers

— Supports variable sized queues and circular queues

— Source and destination address registers are independently configured to post-increment or

remain constant

— Each transfer is initiated by a peripheral, CPU, or eDMA channel request

— Each eDMA channel can optionally send an interrupt request to the CPU on completion of a

single value or block transfer

•

Interrupt controller (INTC)

— 231 interrupt request registers

1

– 208 peripheral interrupt requests

– Eight software settable sources

– 16 reserved

— Unique 9-bit vector per interrupt source

— 16 priority levels with fixed hardware arbitration within priority levels for each interrupt source

— Priority elevation for shared resources

1. Although this device has a maximum of 231interrupts, the logic requires that the total number of interrupts be divisible by four.
Therefore, the total number of interrupts specified for this device is 232.

«
...
37
38
39
40
41
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: Bartlett Страницы: 30

Бренд: Wasp Страницы: 16

Бренд: 2M Technology Страницы: 17

Бренд: 2iB Страницы: 5

Бренд: SYCLOPE Страницы: 60

Бренд: Digiplex Страницы: 48

Бренд: 4IPNET Страницы: 11

Бренд: Swagelok Страницы: 6

Бренд: Invacare Страницы: 44

Бренд: SMC Networks Страницы: 2

Бренд: YASKAWA Страницы: 157

CapSense Plus CY3280-CPM1

Бренд: Cypress Страницы: 4

Бренд: Thevco Страницы: 36

Бренд: Inverter Страницы: 2

NetController B042-004

Бренд: Tripp Lite Страницы: 2

FINGER007 Series

Бренд: IDTECK Страницы: 9

Бренд: Astrapool Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды