Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 931 | Manualshive

Страница: 931 / 1153

background image

Enhanced Serial Communication Interface (eSCI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

20-36

Freescale Semiconductor

LIN

LWAKE

A wake-up character has been received from a LIN frame. The LIN
wake-up (LWAKE) flag is set when the LIN hardware receives a
wake-up character sent by one of the LIN slaves. This occurs only
when the LIN bus is in sleep mode. Clear the LWAKE flag by writing a
1 to the bit.

ESCI

x

_SR[18]

WUIE

LIN

STO

The response of the slave has been too slow (slave timeout). The
slave timeout (STO) flag is set during an RX frame when the LIN slave
has not transmitted all requested data bytes before the specified
timeout period. Clear the STO flag by writing a 1 to the bit.

ESCI

x

_SR[19]

STIE

LIN

PBERR

Physical bus error detected. If the RXD input remains at the same
value for 15 cycles after a transmission has started, the LIN hardware
sets the physical bus error (PBERR) flag. Clear the PBERR flag by
writing a 1 to the bit.

ESCI

x

_SR[20]

PBIE

LIN

CERR

CRC error detected. If an RX frame has the CRC checking flag set,
and the two CRC bytes do not match the calculated CRC pattern, the
CRC error (CERR) flag is set. Clear the CERR flag by writing a 1 to
the bit.

ESCI

x

_SR[21]

CIE

LIN

CKERR

Checksum error detected. If an RX frame has the checksum checking
flag set and the last byte does not match the calculated checksum, the
checksum error (CKERR) flag is set. Clear the CKERR flag by writing
a 1 to the bit.

ESCI

x

_SR[22]

CKIE

LIN

FRC

LIN frame completed. The frame complete (FRC) flag is set after the
last byte of a TX frame is transmitted, or after the last byte of an RX
frame is received. The FRC flag indicates that the next frame can be
set up. Clear the FRC flag by writing a 1 to the bit.

Note:

The last byte of an outgoing TX frame or incoming RX frame
indicates that the checksum comparison occurred.

Note:

It is possible to set the FRC flag before the DMA controller has
completed transferring the last byte from the eSCI port to
system memory. Do not set the FRC flag if the frame will be
processed. For frames that will be processed, use the DMA
controller interrupt.

ESCI

x

_SR[23]

FCIE

LIN

OVFL

ESCIx_LRR overflow. The overflow (OVFL) flag is set when a byte is
received in the ESCI

x

_LRR before the previous byte is read. Since the

system is responsible for reading the register before the next byte
arrives, this condition indicates a problem with CPU load. The OVFL
flag is cleared by writing a 1 to the bit.

ESCI

x

_SR[31]

OFIE

Table 20-21. eSCI Interrupt Flags, Sources, Mask Bits, and Descriptions (continued)

Interrupt

Source

Flag

Description

Source

Local

Enable

«
...
929
930
931
932
933
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Desoutter Страницы: 74

Бренд: Quickie Страницы: 64

Бренд: Allen-Bradley Страницы: 88

Бренд: Lennox Страницы: 34

Бренд: Rohde Страницы: 344

Бренд: QUANT Страницы: 24

Бренд: Aurora Scientific Страницы: 21

Бренд: Clare Controls Страницы: 3

Бренд: Swegon Страницы: 11

Бренд: ICP DAS USA Страницы: 153

Бренд: Omega Страницы: 20

Бренд: digitalview Страницы: 18

Бренд: Nitrous Express Страницы: 20

Бренд: GAC Страницы: 22

Бренд: Zamel Страницы: 2

Бренд: EP Solar Страницы: 3

Бренд: AMALGAMATED INSTRUMENT Страницы: 45

Бренд: Eaton Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды