manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

12-37

An 8-word wrapping burst reads eight 32-bit words by supplying a starting address that points to one of 
the words (doubleword aligned) and requiring the memory device to sequentially drive each word on the 
data bus. The selected slave device must internally increment ADDR[27:29] (also ADDR[30] in the case 
of a 16-bit port size device) of the supplied address for each transfer, until the address reaches an 8-word 
boundary, and then wrap the address to the beginning of the 8-word boundary. The address and transfer 
attributes supplied by the EBI remain stable during the transfers, and the EBI terminates each beat transfer 
by asserting TA. The EBI requires that addresses be aligned to a doubleword boundary on all burst cycles.

Table 12-14

 shows the burst order of beats returned for an 8-word burst to a 32-bit port.

The general case of burst transfers assumes that the external memory has 32-bit port size and 8-word burst 
length. The EBI can also burst from 16-bit port size memories, taking twice as many external beats to fetch 
the data as compared to a 32-bit port with the same burst length. The EBI can also burst from 16-bit or 
32-bit memories that have a 4-word burst length (BL = 1 in the appropriate base register). In this case, two 
external 4-word burst transfers (wrapping on 4-word boundary) are performed to fulfill the internal 8-word 
request. This operation is considered atomic by the EBI, so the EBI does not allow other unrelated master 
accesses or bus arbitration to intervene between the transfers. For more details and a timing diagram, refer 
to 

Section 12.4.2.6.3, “Small Access Example #3: 32-byte Read to 32-bit Port with BL = 1

.”

During burst cycles, the BDIP (burst data in progress) signal is used to indicate the duration of the burst 
data. During the data phase of a burst read cycle, the EBI receives data from the addressed slave. If the 
EBI needs more than one data, it asserts the BDIP signal. Upon receiving the data prior to the last data, the 
EBI negates BDIP. Thus, the slave stops driving new data after it receives the negation of BDIP on the 
rising edge of the clock. Some slave devices have their burst length and timing configurable internally and 
thus may not support connecting to a BDIP pin. In this case, BDIP is driven by the EBI normally, but the 
output is ignored by the memory and the burst data behavior is determined by the internal configuration 
of the EBI and slave device. When the TBDIP bit is set in the appropriate base register, the timing for BDIP 
is altered. Refer to 

Section 12.4.2.5.1, “TBDIP Effect on Burst Transfer

,” for this timing.

Since burst writes are not supported by the EBI

1

, the EBI negates BDIP during write cycles.

Table 12-14. Wrap Bursts Order

 

Burst Starting Address 

ADDR[27:28]

Burst Order

(Using 32-bit Port Size)

00

word0 

−>

 word1 

−>

 word2 

−>

 word3 

−>

 word4 

−>

 word5 

−>

 word6 

−>

 word7

01

word2 

−>

 word3 

−>

 word4 

−>

 word5 

−>

 word6 

−>

 word7 

−>

 word0 

−>

 word1

10

word4 

−>

 word5 

−>

 word6 

−>

 word7 

−>

 word0 

−>

 word1 

−>

 word2 

−>

 word3

11

word6 

−>

 word7 

−>

 word0 

−>

 word1 

−>

 word2 

−>

 word3 

−>

 word4 

−>

 word5

1. Except for the special case of a 32-bit non-chip select access in 16-bit data bus mode. Refer to Section 12.4.2.11.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Eastern Times Technology BT-100 Quick Start Manual preview
BT-100
Бренд: Eastern Times Technology Страницы: 4
Vacon 10 Quick Manual preview
10
Бренд: Vacon Страницы: 18
A10 Harmony Controller 2000 Installation Manual preview
Harmony Controller 2000
Бренд: A10 Страницы: 27
Oceanic DX1 Product Service Manual preview
DX1
Бренд: Oceanic Страницы: 11
KaMo Pearldex Series Manual preview
Pearldex Series
Бренд: KaMo Страницы: 2
Frico ERP Instruction Manual preview
ERP
Бренд: Frico Страницы: 12
Xylem Bell & Gossett Technologic PPS Quick Start Manual preview
Bell & Gossett Technologic PPS
Бренд: Xylem Страницы: 20
Samson 2371-10 Mounting And Operating Instructions preview
2371-10
Бренд: Samson Страницы: 36
Vega VEGATOR 131 Operating Instructions Manual preview
VEGATOR 131
Бренд: Vega Страницы: 28
WATSON W91 Series Installation, Operation & Maintenance Instructions Manual preview
W91 Series
Бренд: WATSON Страницы: 16
Danfoss AME 56 Instructions Manual preview
AME 56
Бренд: Danfoss Страницы: 16
Meilhaus Electronic USB-GT Manual preview
USB-GT
Бренд: Meilhaus Electronic Страницы: 19
Topcon OPUS A3 STANDARD Full Technical Data Sheet preview
OPUS A3 STANDARD Full
Бренд: Topcon Страницы: 10
Leviton DECORA ILLUMATECH IPF01-1LX Installation Instructions preview
DECORA ILLUMATECH IPF01-1LX
Бренд: Leviton Страницы: 2
WAGO 8003 Series Operating And Assembly Instructions preview
8003 Series
Бренд: WAGO Страницы: 2
Martin Audio CMX2A Specification Sheet preview
CMX2A
Бренд: Martin Audio Страницы: 1
digitalview AL-1280 Instructions Manual preview
AL-1280
Бренд: digitalview Страницы: 18
Nitrous Express MAXIMIZER-II Installation And User Manual preview
MAXIMIZER-II
Бренд: Nitrous Express Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды