Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 843 | Manualshive

Страница: 843 / 1153

background image

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

19-20

Freescale Semiconductor

The following table describes the fields in the DSPI status register:

Table 19-6. DSPI

x

_SR Field Descriptions

Field

Description

0

TCF

Transfer complete flag. Indicates that all bits in a frame have been shifted out. The TCF bit is set after the
last incoming databit is sampled, but before the tASC delay starts. Refer to

Section 19.4.7.1, “Classic SPI

Transfer Format (CPHA = 0)

” for details. The TCF bit is cleared by writing 1 to it.

0 Transfer not complete
1 Transfer complete

1

TXRXS

TX and RX status. Reflects the status of the DSPI. Refer to

Section 19.4.2, “Start and Stop of DSPI

” for information on what clears and sets this bit.

0 TX and RX operations are disabled (DSPI is in STOPPED state)
1 TX and RX operations are enabled (DSPI is in RUNNING state)

2

Reserved.

3

EOQF

End of queue flag. Indicates that transmission in progress is the last entry in a queue. The EOQF bit is set
when the TX FIFO entry has the EOQ bit set in the command halfword and after the last incoming databit
is sampled, but before the tASC delay starts. Refer to

Section 19.4.7.1, “Classic SPI Transfer Format (CPHA

” for details.

The EOQF bit is cleared by writing 1 to it. When the EOQF bit is set, the TXRXS bit is automatically cleared.
0 EOQ is not set in the executing command
1 EOQ bit is set in the executing SPI command

Note:

EOQF does not function in slave mode.

4

TFUF

Transmit FIFO underflow flag. Indicates that an underflow condition in the TX FIFO has occurred. The
transmit underflow condition is detected only for DSPI modules operating in slave mode and SPI
configuration. The TFUF bit is set when the TX FIFO of a DSPI operating in SPI slave mode is empty, and
a transfer is initiated by an external SPI master. The TFUF bit is cleared by writing 1 to it.

0 TX FIFO underflow has not occurred
1 TX FIFO underflow has occurred

5

Reserved.

6

TFFF

Transmit FIFO fill flag. Indicates that the TX FIFO can be filled. Provides a method for the DSPI to request
more entries to be added to the TX FIFO. The TFFF bit is set while the TX FIFO is not full. The TFFF bit can
be cleared by writing 1 to it, or an by acknowledgement from the eDMA controller when the TX FIFO is full.

0 TX FIFO is full
1 TX FIFO is not full

7–11

Reserved.

12

RFOF

Receive FIFO overflow flag. Indicates that an overflow condition in the RX FIFO has occurred. The bit is set
when the RX FIFO and shift register are full and a transfer is initiated. The bit is cleared by writing 1 to it.

0 RX FIFO overflow has not occurred
1 RX FIFO overflow has occurred

13

Reserved.

«
...
841
842
843
844
845
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Falcon Страницы: 3

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: G1SLE Страницы: 2

Бренд: Hafele Страницы: 82

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренд: ITALFARAD Страницы: 32

Бренд: Danfoss Страницы: 30

Бренд: Apricus Страницы: 32

Linear Technology ADI Power DC3017A

Бренд: Analog Devices Страницы: 12

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: Variotech Страницы: 24

Бренд: Current Страницы: 4

Бренд: PEAS Страницы: 4

Бренд: Sollae Systems Страницы: 72

Бренд: Invacare Страницы: 44

Бренд: HIKVISION Страницы: 5

Бренд: Nexen Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды