Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 858 | Manualshive

Страница: 858 / 1153

background image

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

19-35

The SPI and DSI configurations are valid in slave mode. CSI configuration is not available in slave mode.
In SPI slave mode the slave transfer attributes are set in the DSPI

x

_CTAR0. In DSI slave mode the slave

transfer attributes are set in the DSPI

x

_CTAR1. In slave mode, for both SPI and DSI configurations, data

is transferred MSB first. The LSBFE field of the associated CTAR is ignored.

19.4.1.3

Module Disable Mode

The module disable mode is used for MCU power management. The clock to the non-memory mapped
logic in the DSPI is stopped while in module disable mode. The DSPI enters the module disable mode
when the MDIS bit in DSPI

x

_MCR is set.

Refer to

Section 19.4.10, “Power Saving Features

,” for more details on the module disable mode.

19.4.1.4

Debug Mode

The debug mode is used for system development and debugging. If the MCU enters debug mode while the
FRZ bit in the DSPI

x

_MCR is set, the DSPI stops all serial transfers and enters a stopped state. If the MCU

enters debug mode while the FRZ bit is cleared, the DSPI behavior is unaffected and remains dictated by
the module-specific mode and configuration of the DSPI. The DSPI enters debug mode when a debug
request is asserted by an external controller.

Refer to

for a state diagram.

19.4.2

Start and Stop of DSPI Transfers

The DSPI has two operating states: STOPPED and RUNNING. The states are independent of DSPI
configuration. The default state of the DSPI is STOPPED. In the STOPPED state no serial transfers are
initiated in master mode and no transfers are responded to in slave mode. The STOPPED state is also a
safe state for writing the various configuration registers of the DSPI without causing undetermined results.
The TXRXS bit in the DSPI

x

_SR is cleared in this state. In the RUNNING state, serial transfers take place.

The TXRXS bit in the DSPI

x

_SR is set in the RUNNING state.

shows a state diagram of the start and stop mechanism.

Figure 19-18. DSPI Start and Stop State Diagram

RUNNING

TXRXS = 1

STOPPED

TXRXS = 0

RESET

Power-on-Reset

0

1

2

«
...
856
857
858
859
860
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: S&C Страницы: 34

Бренд: Particle Страницы: 6

Бренд: Galcon Страницы: 32

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Wesa Страницы: 8

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: Cruisair Страницы: 30

Бренд: KEPCO Страницы: 34

Бренд: jbc Страницы: 8

Бренд: Extron electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды