Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 821 | Manualshive

Страница: 821 / 1153

background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-122

Freescale Semiconductor

.

The eQADC and QADC also have similar procedures for the configuration or execution of applications.

shows the steps required for the QADC versus the steps required for the eQADC system.

Table 18-59. Terminology Comparison between QADC and eQADC

QADC Terminology

eQADC Terminology

Function

CCW

Command Message

In the QADC, the hardware only executes conversion command words.
In the eQADC, not all commands are conversion commands; some are
configuration commands.

Queue Trigger

CFIFO Trigger

In the QADC, a trigger event is required to start the execution of a queue.
In the eQADC, a trigger event is required to start command transfers from a
CFIFO. When a CFIFO is triggered and transferring, commands are
continuously moved from command queues to CFIFOs. Thus, the trigger
event initiates the “execution of a queue” indirectly.

Command Word Pointer
Queue

n

(CWPQ

n

)

Counter Value of
Commands Transferred
from Command FIFO

n

(TC_CF

n

)

In the QADC, CWPQ

n

allows the last executed command on queue

n

to be

determined.
In the eQADC, the TC_CF

n

value allows the last transferred command on

command queue

n

to be determined.

Queue Pause Bit (P)

CFIFO Pause Bit

In the QADC, detecting a pause bit in the CCW pauses the queue execution.
In the eQADC, detecting a pause bit in the command pauses command
transfers from a CFIFO.

Queue Operation Mode
(MQ

n

)

CFIFO Operation Mode
(MODE

n

)

The eQADC supports all queue operation modes in the QADC except
operation modes related to a periodic timer. A timer elsewhere in the system
can provide the same functionality if it is connected to ETRIG

n

.

Queue Status (QS)

CFIFO Status (CFS

n

)

In the QADC, the queue status is read to check whether a queue is idle,
active, paused, suspended, or trigger pending.
In the eQADC, the CFIFO status is read to check whether a queue is IDLE,
WAITING FOR TRIGGER (idle or paused in QADC), or triggered
(suspended or trigger pending in QADC).

Table 18-60. Usage Comparison between QADC and eQADC System

Procedure

QADC

eQADC System

Analog Control Configuration

Configure analog device by writing to
the QADCs.

Program configuration commands into
command queues.

Prepare Scan Sequence

Program scan commands into
command queues.

Program scan commands into
command queues.

Queue Control Configuration

Write to the QADC control registers.

Write to the eQADC control registers.

Data Transferred between
Queues and Buffers

Not Required.

Program the eDMA or the CPU to
handle the data transfer.

Serial Interface Configuration

Not Required.

Write to the eQADC SSI registers.

Queue Execution

Require software or external trigger
events to start queue execution.

Require software or external trigger
events to start command transfers from
a CFIFO.

«
...
819
820
821
822
823
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ZKTeco Страницы: 123

Бренд: Facility Explorer Страницы: 4

Бренд: Badger Meter Страницы: 20

Бренд: Daikin Страницы: 5

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

Бренд: Eaton Страницы: 2

Бренд: Cadac Страницы: 4

Бренд: ZKTeco Страницы: 11

Бренд: Phoenix Contact Страницы: 56

Бренд: OBO Bettermann Страницы: 6

Integrated Controller Rev C EZ-ZONE PM

Бренд: Watlow Страницы: 80

M2M Smart Service Developer Kit

Бренд: Kontron Страницы: 27

SmartLoop KTSL-FC1-UV-KO

Бренд: Keystone Страницы: 2

xComfort CJAU-01 Series

Бренд: Eaton Страницы: 4

Бренд: Datapath Страницы: 16

Бренд: Collcomm Страницы: 16

Legend LX Second Stage

Бренд: Aqua Lung Страницы: 18

Бренд: Hanna Instruments Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды