manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-61

 

•

Upon data trace write/read after the previous DTM message was lost due to a collision entering the 
FIFO between the DTM message and any of the following: watchpoint message, ownership trace 
message, or branch trace message

Data trace synchronization messages provide the full address (without leading zeros) and insure that 
development tools fully synchronize with data trace regularly. Synchronization messages provide a 
reference address for subsequent data messages, in which only the unique portion of the data trace address 
is transmitted. The format for data trace write/read with sync. messages is as follows:

Figure 24-46. Data Write/Read with Sync. Message Format

Exception conditions that result in data trace synchronization are summarized in 

Table 24-37

.

Table 24-37. Data Trace Exception Summary

Exception Condition

Exception Handling

System Reset Negation

At the negation of JTAG reset (JCOMP), queue pointers, counters, state machines, 
and registers within the NZ6C3 module are reset. If data trace is enabled, the first 
data trace message is a data write/read with sync. message.

Data Trace Enabled

The first data trace message (after data trace has been enabled) is a 
synchronization message.

Exit from Low Power/Debug Upon exit from a low power mode or debug mode the next data trace message will 

be converted to a data write/read with sync. message.

Queue Overrun

An error message occurs when a new message cannot be queued due to the 
message queue being full. The FIFO will discard messages until it has completely 
emptied the queue. After it is emptied, an error message will be queued. The error 
encoding will indicate which types of messages attempted to be queued while the 
FIFO was being emptied. The next DTM message in the queue will be a data 
write/read with sync. message.

Periodic Data Trace Sync.

A forced synchronization occurs periodically after 255 data trace messages have 
been queued. A data write/read with sync. message is queued. The periodic data 
trace message counter then resets.

Event In

If the Nexus module is enabled, a EVTI assertion initiates a data trace write/read 
with sync. message upon the next data write/read (if data trace is enabled and the 
EIC bits of the DC1 register have enabled this feature).

Attempted Access to Secure 
Memory

For devices which implement security, any attempted read or write to secure 
memory locations will temporarily disable data trace & cause the corresponding 
DTM to be lost. A subsequent read/write will queue a data trace read/write with 
sync. message.

Collision Priority

All messages have the following priority: WPM 

−>

 OTM 

−>

 BTM 

−>

 DTM. A DTM 

message which attempts to enter the queue at the same time as a watchpoint 
message or ownership trace message or branch trace message will be lost. A 
subsequent read/write will queue a data trace read/write with sync. message.

DATA

MSB

LSB

2

3

4

F-ADDR

DSZ

SRC

5

4 bits

1

TCODE (001101 or 001110)

3 bits

1-32 bits

1-64 bits

6 bits

Max length = 109 bits; Min length = 15 bits

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Бренд: Nidec Страницы: 20
UE 120 Series Installation And Maintenance Instructions preview
120 Series
Бренд: UE Страницы: 4
Badger Meter PC100 Installation And Operation Manual preview
PC100
Бренд: Badger Meter Страницы: 20
Gardena Master Operator'S Manual preview
Master
Бренд: Gardena Страницы: 18
Danfoss VLT Micro Drive FC 51 Series Quick Manual preview
VLT Micro Drive FC 51 Series
Бренд: Danfoss Страницы: 23
H3C WX Series Configuration Manual preview
WX Series
Бренд: H3C Страницы: 69
Jands 4PAK Operating Manual preview
4PAK
Бренд: Jands Страницы: 6
L. G. B. 51099 Instructions preview
51099
Бренд: L. G. B. Страницы: 2
L-Acoustics LA4X Product Information preview
LA4X
Бренд: L-Acoustics Страницы: 36
National Instruments RMC-8354 User Manual preview
RMC-8354
Бренд: National Instruments Страницы: 102
NAU ROBOTICS RC40A Operating Instruction preview
RC40A
Бренд: NAU ROBOTICS Страницы: 109
Native Instruments Maschine Mikro MK2 Getting Started preview
Maschine Mikro MK2
Бренд: Native Instruments Страницы: 181
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Бренд: u-blox Страницы: 2
Vaillant VRT 350f Installation Instructions Manual preview
VRT 350f
Бренд: Vaillant Страницы: 36
Vaillant VRT 350 Installation Instructions Manual preview
VRT 350
Бренд: Vaillant Страницы: 28
Vaillant VAZ CPC Operating Instructions Manual preview
VAZ CPC
Бренд: Vaillant Страницы: 92
Bettis TEC2 Quick Start Manual preview
TEC2
Бренд: Bettis Страницы: 18
Murphy MURPHYMATIC ASM160 Installation And Operation Instructions preview
MURPHYMATIC ASM160
Бренд: Murphy Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды