Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 1153

background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

6-14

Freescale Semiconductor

Except for a POR request or writing a 1 to the software external reset flag (SERF) bit, all reset requests,
regardless of priority are not serviced until the current reset completes.

In the following cases, more than one reset bit is set in the reset status register (SIU_RSR):

29–30

BOOTCFG

Reset configuration pin status.
BOOTCFG[0:1] identifies the address of the reset configuration halfword (RCHW) and whether arbitration is used
by the boot assist module (BAM).

00

Internal boot mode – lowest address (0x0000_0000) from one of the six LAS fields in internal flash memory.

01

Serial boot mode – lower halfword of the censorship control word.

10

External boot mode – lowest address (0x0000_0000) of external memory as defined by the
chip select 0 (CS[0]) signal with no external arbitration.

11

Invalid value.

If RSTCFG does not assert before RSTOUT negates, and the lower half of the censorship control word (least

significant halfword) equals 0xFFFF or 0x0000, the BOOTCFG field is set to 0b10.

Otherwise, if the RSTCFG pin was negated at the last negation of RSTOUT, and the lower half of the censorship
control word does not equal 0xFFFF or 0x0000, then the BOOTCFG field is set to the value 0b00.

Refer to

for a description of RCHW.

31

RGF

Reset glitch flag.
Set by the reset controller when a glitch is detected on the RESET pin. This bit is cleared by the assertion of the
power-on reset input to the reset controller, or a write of 1 to the RGF bit. Refer to

Section 6.4.2.1, “RESET Pin

,” for more information on glitch detection.

0

No glitch has been detected on the RESET pin.

1

A glitch has been detected on the RESET pin.

Table 6-9. Causes That Set Multiple Reset Status Bits

Case 1

Condition

• POR request negates and the device remains in the reset
• External reset requested
• POR and external reset status bits are set

Reason

POR request started the reset sequence, but an external reset request was received before the POR reset
sequence ended.

Case 2

Condition

• Software external reset requested
• SERF flag bit set but no previously set bits in the SIU_RSR are cleared

Reason

The SERF flag bit is cleared by writing a 1 (write 1 to clear) to the bit location or when another reset source
is asserted.

Table 6-8. SIU_RSR Field Descriptions (continued)

Field

Description

«
...
187
188
189
190
191
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Paoli Страницы: 16

Бренд: OEG Страницы: 168

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: Kantronics Страницы: 201

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

Бренд: Haiwell Страницы: 18

Бренд: Melexis Страницы: 13

Бренд: ICP DAS USA Страницы: 20

Бренд: iNels Страницы: 2

Бренд: Technische Alternative Страницы: 124

NetworkHD 200 series

Бренд: Wyrestorm Страницы: 4

Бренд: Tech Controllers Страницы: 20

Бренд: Cablematic Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды