Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 1153

background image

Reset

MPC5565 Microcontroller Reference Manual, Rev. 1.0

4-16

Freescale Semiconductor

If the RCHW stored in either internal or external flash is invalid (boot identifier field of RCHW is not
0x5A), or if BOOTCFG[0] negates and BOOTCFG[1] asserts when RSTOUT negates, then RCHW is not
applicable, and serial boot mode is invoked.

summarizes the RCHW location options.

4.4.4

Reset Configuration Timing

The timing diagram in

shows the sampling of the BOOTCFG[0:1], WKPCFG, and

PLLCFG[0:1] pins for a power-on reset. The timing diagram is also valid for internal/external resets
assuming that V

DD,

V

DDSYN,

and V

DDEH6

are within valid operating ranges. The values of the

PLLCFG[0:1] pins are latched at the negation of the RSTOUT pin, if the RSTCFG pin is asserted at the
negation of RSTOUT. The value of the WKPCFG signal is applied at the assertion of the internal reset
signal (as indicated by the assertion of RSTOUT). The values of the WKPCFG and BOOTCFG[0:1] pins
are latched 4 clock cycles before the negation of RSTOUT and stored in the reset status register
(SIU_RSR). BOOTCFG[0:1] are latched only if RSTCFG is asserted. WKPCFG is not dependent on
RSTCFG.

Table 4-10. Reset Configuration Halfword Sources

RSTCFG

BOOTCFG[0]

BOOTCFG[1]

Boot Identifier

Field

(RCHW)

Boot Mode

Configuration Word Source

1

—

—

Valid

Internal

The lowest address of one of the six low address
spaces (LAS) in internal flash memory.

Invalid

Serial

Not applicable

0

0

0

Valid

Internal

The lowest address of one of the six low address
spaces (LAS) in internal flash memory.

Invalid

Serial

Not applicable

0

0

1

—

Serial

Not applicable

0

1

0

Valid

External boot,
no arbitration

The lowest address (0x0000_0000) of an external
memory device, enabled by chip select CS[0] using
either 16- or 32-bit data bus.

Invalid

Serial

Not applicable

0

1

1

External arbitration not supported

«
...
155
156
157
158
159
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Aalborg Страницы: 48

Бренд: Danfoss Страницы: 32

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 4

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: National Instruments Страницы: 2

Бренд: RadioMaster Страницы: 10

Бренд: Auber Страницы: 3

Бренд: Grundfos Страницы: 80

Бренд: Digiplex Страницы: 48

Бренд: Haiwell Страницы: 18

Бренд: D+H Страницы: 20

Бренд: Freescale Semiconductor Страницы: 41

Бренд: H3C Страницы: 15

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды