Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 158

Страница: 158 / 1153

Reset

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

4-17

The following figure shows the reset configuration timing:

Figure 4-4. Reset Configuration Timing

RSTOUT

RESET

Internal
reset

POR

PLL

PLL locks

RSTCFG

Crystal powering up or acquiring lock

WKPCFG and BOOTCFG
are latched. PLLCFG and

User drives

config pins relative

to RSTOUT

PLLCFG and RSTCFG are

(4 clock cycles)

PLL locked

2400

clock cycles

‘Don’t Care’ and WKPCFG is
treated as ‘1’ during POR assertion.

PLLCFG, RSTCFG and WKPCFG
are applied, but not latched.

RSTCFG still applied

This clock count is dependent on the configuration of the FMPLL (Refer to

Section 4.2.2, “RSTOUT

”). If the FMPLL is configured

for 1:1 (dual controller) operation or for bypass mode, this clock count is 16000.

All reset signals
negated (2404 cycles)

PLLCFG is latched.
RSTCFG is no longer

used.

but not latched.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды