Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1006 | Manualshive

Страница: 1006 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-13

24.4.5

System Clock Locked Indication

Following a power-on reset, the lsb of the auxiliary output port pins (MDO0) can be monitored to provide
the lock status of the system clock. MDO0 is driven to a logic 1 until the system clock achieves lock after
exiting power-on reset. After the system clock is locked, MDO0 is negated and tools may begin Nexus
configuration. Loss of lock conditions that occur subsequent to the exit of power-on reset and the initial
lock of the system clock do not cause a Nexus reset, and therefore do not result in MDO0 driven high.

24.5

Nexus Port Controller (NPC)

The Nexus port controller (NPC) is that part of the NDI that controls access and arbitration of the device’s
internal Nexus modules. The NPC contains the port configuration register (PCR) and the device
identification register (DID). The contents of the NPC DID are the same as the JTAGC device
identification register.

24.5.1

Overview

The device incorporates multiple modules that require development support. Each of these modules
implements a development interface based on the IEEE-ISTO 5001-2001 standard and must share the
input and output ports that interface with the development tool. The NPC controls the usage of these ports
in a manner that allows the individual modules to share the ports, while appearing to the development tool
as a single module.

24.5.2

Features

The NPC performs the following functions:

•

Controls arbitration for ownership of the Nexus auxiliary output port

•

Nexus device identification register and messaging

•

Generates MCKO enable and frequency division control signals

•

Controls sharing of EVTO

•

Control of the device-wide debug mode

•

Generates asynchronous reset signal for Nexus modules based on JCOMP input, censorship status,
and power-on reset status

•

System clock locked status indication via MDO[0] during Nexus reset

•

Provides Nexus support for censorship mode

Table 24-8. SRC Packet Encodings

SRC[3:0]

Client

0b0000

e200z

6

0b0001

eDMA

0b0101-0b1111

Reserved

«
...
1004
1005
1006
1007
1008
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ZKTeco Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: York Страницы: 24

Бренд: TECH Страницы: 20

Бренд: ProMinent Страницы: 2

Бренд: Jordan Valve Страницы: 5

ENFORCER SLI PR-B1124-PQ

Бренд: SECO-LARM Страницы: 2

Бренд: ULTRAFRYER Страницы: 1

Бренд: Suzhou Lily Страницы: 8

TACOTHERM FRESH PETA ES 5941S

Бренд: Taconova Страницы: 40

MC DC-2.00 Series

Бренд: Hanbay Страницы: 7

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Brook Страницы: 15

Бренд: DMC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды