manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

1-1

 

Chapter 1  
Introduction

1.1

Overview 

The MPC5565 microcontroller (MCU) is a member of the MPC5500 family of next generation powertrain 
microcontrollers built on Power Architecture

™

 technology. The MPC5500 family contains a host 

processor core that complies with the Power Architecture embedded category, which is 100 percent user 
mode compatible with the original Power PC

™

 user instruction set architecture (UISA). This family of 

parts contains many new features coupled with high-performance CMOS technology to provide significant 
performance improvement over the MPC565. 

The e200z6 CPU of the MPC5500 family is part of the family of CPU cores that implement versions built 
on the Power Architecture embedded category. This core also has additional instructions, including digital 
signal processing (DSP) instructions, beyond the classic PowerPC instruction set.

The MPC5565 has two levels of memory hierarchy. The fastest accesses are to the 8 KB unified cache. 
The next level in the hierarchy contains up to 80 KB of internal SRAM and 2 MB flash memory. Both the 
internal SRAM and the flash memory can hold instructions and data. The external bus interface is designed 
to support most of the standard memories used with the MPC5xx family. 

The complex I/O timer functions of the MPC5500 family are performed by an enhanced time processor 
unit engine (eTPU). The eTPU engine controls 32 hardware channels. The eTPU has been enhanced over 
the TPU by providing 24-bit timers, double-action hardware channels, a variable number of parameters 
per channel, angle clock hardware, and additional control and arithmetic instructions. The eTPU can be 
programmed using a high-level programming language. The less complex timer functions of the MPC5500 
family are performed by the enhanced modular input/output system (eMIOS). The eMIOS’ 24 hardware 
channels are capable of single action, double action, pulse-width modulation (PWM), and modulus counter 
operation. Motor control capabilities include edge-aligned and center-aligned PWM.

Off-chip communication is performed by a suite of serial protocols including: three controller area 
networks (FlexCANs); three enhanced deserial/serial peripheral interface (DSPIs); and two enhanced 
serial communications interfaces (eSCIs).

The DSPIs support pin reduction through hardware serialization and deserialization of timer channels and 
general-purpose input/output (GPIO) signals. 

The MCU has two on-chip 40-channel enhanced queued dual analog to digital converters (eQADC).

The system integration unit (SIU) performs several chip-wide configuration functions. Pad configuration 
and general-purpose input and output (GPIO) are controlled from the SIU. External interrupts and reset 
control are also found in the SIU. The internal multiplexer submodule (SIU_DISR) provides multiplexing 
of eQADC trigger sources, daisy chaining the DSPIs, and external interrupt signal multiplexing.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ABB ACS880 Series Supplement Manual preview
ACS880 Series
Бренд: ABB Страницы: 50
ZKTeco SC800 User Manual preview
SC800
Бренд: ZKTeco Страницы: 123
Paratec TE Series User Manual preview
TE Series
Бренд: Paratec Страницы: 8
J+J S2 Handbook preview
S2
Бренд: J+J Страницы: 33
Caen V793 Technical Information Manual preview
V793
Бренд: Caen Страницы: 20
OJ Electronics OJ-Air2-WP55 Instructions Manual preview
OJ-Air2-WP55
Бренд: OJ Electronics Страницы: 8
Qorvo QM33120WDK1 Quick Start Manual preview
QM33120WDK1
Бренд: Qorvo Страницы: 6
A10 Networks Harmony 2000 Quick Start Manual preview
Harmony 2000
Бренд: A10 Networks Страницы: 2
Go Power 10 AMP RVC-MPPT User Manual preview
10 AMP RVC-MPPT
Бренд: Go Power Страницы: 17
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Бренд: SUPMEA Страницы: 32
Ayra 9000-0043-8700 User Manual preview
9000-0043-8700
Бренд: Ayra Страницы: 19
CDVI Ievo User Manual preview
Ievo
Бренд: CDVI Страницы: 24
National Instruments AMUX-64T Installation Manual preview
AMUX-64T
Бренд: National Instruments Страницы: 3
Kelly KLS14801-8080N User Manual preview
KLS14801-8080N
Бренд: Kelly Страницы: 43
Quicksmart EtherRain User Manual preview
EtherRain
Бренд: Quicksmart Страницы: 10
Aerotech Ensemble HLe Hardware Manual preview
Ensemble HLe
Бренд: Aerotech Страницы: 112
ZEDAR Regency Owner'S Manual preview
Regency
Бренд: ZEDAR Страницы: 25
Elsner Solexa 230V Installation And Adjustment Manual preview
Solexa 230V
Бренд: Elsner Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды