Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 668 | Manualshive

Страница: 668 / 1153

background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

17-13

17.3.2.1

Time Base Clock Signal (TCRCLK[A])

The TCRCLK[A] input signals are used to control the TCR1 and TCR2 time bases for eTPU A.

NOTE

Throughout this document, TCRCLKA is referred to generically as
TCRCLK.

There is one independent TCRCLK input for each engine.

shows the TCRCLK pin

connections. For pulse accumulator operations TCRCLK can be used as a gate for a counter based on the
system clock divided by eight. For angle operations TCRCLK can be used to get the tooth transition
indications in angle mode. Refer to the

eTPU Reference Manual’s

Sections 5.9 and 5.10.

17.3.2.2

Channel Output Disable Signals

Each eTPU engine has four input signals that are used to force the outputs of a group of 8 channels to an
inactive level. These signals originate from the eMIOS. When an output disable signal is active, all the
eight channels assigned to the disable signal that have their ODIS bits set to one in ETPU_C

n

CR register

have their outputs forced to the opposite of the value specified in the ETPU_C

n

CR[OPOL] bit. Therefore,

individual channels can be selected to be affected by the output disable signals, as well as their disabling
forced polarity.

Refer to

Section 16.2.1.1, “Output Disable Input—eMIOS Output Disable Input Signals

information on the output disable signals.

The output disable channel groups are defined in

1

The channel numbers for some of the DSPI channels connections are reversed, for example if eTPU A[16:19] is mapped to
DSPI B[7:4], then eTPU A[16] is connected to DSPI B[7], eTPU A[17] is connected to DSPI B[6],..., and eTPU A[19] is
connected to DSPI B[4]

Table 17-2. MPC5565 TCRCLK Signal

Signal Name

Pin Assignment

I/O

Pin Connection

496 BGA

324 BGA

TCRCLKA_
IRQ[7]_
GPIO[113]

Primary
Alternate
General-purpose I/O

I
I

I/O

M2

M2

Table 17-3. Output Disable Channel Groups

eMIOS Channel

Engine

eTPU Channels Disabled

11

A

0–7

10

8–15

9

16–23

8

24–31

«
...
666
667
668
669
670
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: YASKAWA Страницы: 256

Бренд: Hanna Instruments Страницы: 88

Бренд: Eaton Страницы: 4

Бренд: Kampmann Страницы: 5

Бренд: Auber Страницы: 3

Бренд: Woodward Страницы: 32

Бренд: Neets Control Страницы: 12

Бренд: Grundfos Страницы: 80

Бренд: LEGRAND Страницы: 10

Бренд: Xylem Страницы: 28

Бренд: Overland Storage Страницы: 4

Бренд: VALPES Страницы: 28

Бренд: Magpowr Страницы: 22

Fair-Play MP-50 Series

Бренд: Translux Страницы: 20

Бренд: jbc Страницы: 8

Бренд: PROEL Страницы: 34

Бренд: Rain Bird Страницы: 104

SUNEXPLORER III Series

Бренд: Atkinson Electronics Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды