Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1011 | Manualshive

Страница: 1011 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-18

Freescale Semiconductor

describes the NPC reset configuration options.

24.7.2

Auxiliary Output Port

The auxiliary output port is shared by each of the Nexus modules on the device. The NPC communicates
with each of the individual modules and arbitrates for access to the port. Additional information about the
auxiliary port is found in

Section 24.2, “External Signal Description

.”

24.7.2.1

Output Message Protocol

The protocol for transmitting messages via the auxiliary port is accomplished with the MSEO functions.
The MSEO pins are used to signal the end of variable-length packets and the end of messages. They are
not required to indicate the end of fixed-length packets. MDO and MSEO are sampled on the rising edge
of MCKO.

Table 24-12. NPC Reset Configuration Options

JCOMP

Asserted?

PCR[MCKO_EN]

PCR[FPM]

Configuration

No

X

X

Reset

Yes

0

X

Disabled

Yes

1

1

Full-Port Mode

Yes

1

0

Reduced-Port Mode

«
...
1009
1010
1011
1012
1013
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: Abicor Binzel Страницы: 8

Бренд: RadioMaster Страницы: 10

Бренд: Ultraflex Страницы: 7

Бренд: National Instruments Страницы: 78

Бренд: Samson Страницы: 70

Бренд: NXP Semiconductors Страницы: 20

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Neets Control Страницы: 12

Бренд: Consort Страницы: 4

Бренд: Danfoss Страницы: 36

Бренд: Sturtevant Richmont Страницы: 73

Бренд: Patton Страницы: 56

Бренд: Beckhoff Страницы: 67

Бренд: Omron Страницы: 12

fantech IPF05-1L

Бренд: SystemAir Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды