Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 1153

background image

Introduction

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

1-5

•

Frequency modulated phase-locked loop (FMPLL)

— Input clock frequency: 8–20 MHz

— Current controlled oscillator (ICO) range from 48 MHz to maximum device frequency

— Reduced frequency divider (RFD) for reduced frequency operation without re-lock

— Four selectable modes of operation

— Programmable frequency modulation

— Lock detect circuitry continuously monitors lock status

— Loss-of-clock (LOC) detection for reference and feedback clocks

— Self-clocked mode (SCM) operation

— On-chip loop filter (reduces number of external components required)

— Engineering clock output configurable to divide-by-2 to 126 of the system clock frequency

•

External bus interface (EBI)

— 1.8

–

3.3 V nominal I/O voltage

— 324 BGA: 16-bit data bus, 20-bit address bus is default, but configurable to 24-bit address bus.

Although this device is designed to support a 32-bit EBI data bus, only 16 data bus pins are
available and connected on the 324 BGA package. The 496-pin VertiCal assembly provides the
calibration functionality.

— Memory controller with support for various memory types

– Non-burst SDR flash and SRAM

– Asynchronous/legacy flash and SRAM

– Most standard memories used with the MPC5xx family

— Configurable bus speed modes

– 50% of system frequency

– 25% of system frequency

— Support for external master accesses to internal addresses

— Burst support

— Bus monitor

– User selectable

– Programmable timeout period (with eight external bus clock resolution)

— Four chip selects: CS[0:3] multiplexed with ADDR[8:11].

— Two write/byte enable (WE/BE[0:1]) signals in the 324-pin package and the 496 pin assembly.

— Configurable wait states (via chip selects)

— Optional automatic CLKOUT gating to save power and reduce EMI

— Compatible with MPC5xx external bus (with some limitations):

Selectable drive strengths; 10 pF, 20 pF, 30 pF, 50 pF

•

Calibration bus interface

— Calibration bus interface only accessible through 496-pin VertiCal assembly top connector

— 1.8–3.3 V nominal I/O voltage

«
...
38
39
40
41
42
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: e-BLEACH Страницы: 24

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: Samson Страницы: 48

Бренд: L-Acoustics Страницы: 20

Бренд: Koer Страницы: 6

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: Curtis Страницы: 30

Бренд: Danfoss Страницы: 22

ACT4910EVK1-121

Бренд: Active-semi Страницы: 15

MC-3000L-TC Series

Бренд: Lintec Страницы: 2

Chorus GW 90 740

Бренд: Gewiss Страницы: 44

Бренд: Control 4 Страницы: 2

Бренд: Carel Страницы: 2

Бренд: Abov Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды