manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Frequency Modulated Phase Locked Loop and System Clocks (FMPLL)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

11-11

 

NOTE

In addition to supplying power for the CLKOUT signal, when the FMPLL 
is configured for external reference mode of operation, the V

DDE5 

supply 

voltage also controls the voltage level at which the signal presented to the 
EXTAL_EXTCLK pin causes a switch in the clock logic levels. The 
EXTAL_EXTCLK accepts a clock source with a voltage range of 1.6–3.6 V, 
however the transition voltage is determined by V

DDE5

 supply voltage 

divided by two. As an example, if V

DDE5 

is 3.3 V, then the clock transitions 

at approximately 1.6 V. The V

DDE5

 supply voltage and the voltage level of 

the external clock reference must be compatible, or the device does not 
clock properly.

11.1.4.3

Bypass Mode

In FMPLL bypass mode, the FMPLL is completely bypassed and the user must supply an external clock 
on the EXTAL_EXTCLK pin. The external clock is used directly to produce the internal system clocks. 
In bypass mode, the analog portion of the FMPLL is disabled and no clocks are generated at the FMPLL 
output. Consequently, frequency modulation is not available. In bypass mode the pre-divider is bypassed 
and has no effect on the system clock. The frequency in bypass mode is F

ref_ext

.

To enter bypass mode, the default FMPLL configuration must be overridden by following the procedure 
outlined in 

Section 11.1.4, “FMPLL Modes of Operation

.” A block diagram illustrating bypass mode is 

shown in 

Figure 11-2

.

11.1.4.4

Dual-Controller Mode (1:1)

FMPLL dual-controller mode is used by the slave MCU device of a dual-controller system. The slave 
FMPLL facilitates skew reduction between the input and output clock signals. To enter dual-controller 
mode, the default FMPLL configuration must be overridden by the procedure outlined in 

Section 11.1.4, 

“FMPLL Modes of Operation

.” 

In this mode, the system clock runs at twice the frequency of the EXTAL_EXTCLK input pin and is phase 
aligned. Note that crystal operation is not supported in dual-controller mode and an external clock must be 
provided. In this mode, the frequency and phase of the signal at the EXTAL_EXTCLK pin and the 
CLKOUT pin of the slave MCU are matched. A block diagram illustrating dual-controller mode (1:1) is 
shown in 

Figure 11-6

.

Frequency modulation is not available when configured for dual-controller mode for both the master and 
slave devices. Enabling frequency modulation on the device supplying the reference clock to the slave in 
dual-controller mode produces unreliable clocks on the slave.

NOTE

When configured for dual-controller mode, the CLKOUT clock divider on 
the slave device must not be changed from its reset state of divide-by-two. 
Increasing or decreasing this divide ratio produces unpredictable results 
from the FMPLL.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Eastern Times Technology BT-100 Quick Start Manual preview
BT-100
Бренд: Eastern Times Technology Страницы: 4
Vacon 10 Quick Manual preview
10
Бренд: Vacon Страницы: 18
Hach SC1500 User Manual preview
SC1500
Бренд: Hach Страницы: 86
Fantech ECO-TOUCH Operating Manual preview
ECO-TOUCH
Бренд: Fantech Страницы: 2
RadioMaster POCKET Quick Start Manual preview
POCKET
Бренд: RadioMaster Страницы: 10
HANYOUNG NUX NP100 Manual preview
NP100
Бренд: HANYOUNG NUX Страницы: 36
HANYOUNG NUX HY Series Instruction Manual preview
HY Series
Бренд: HANYOUNG NUX Страницы: 4
MADRIX Nebula User Manual preview
Nebula
Бренд: MADRIX Страницы: 91
MADRIX Nebula Quick Start Manual preview
Nebula
Бренд: MADRIX Страницы: 40
YASKAWA MP Series Driver Manual preview
MP Series
Бренд: YASKAWA Страницы: 18
Oceanic DX1 Product Service Manual preview
DX1
Бренд: Oceanic Страницы: 11
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Бренд: Parker Страницы: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Бренд: Parker Страницы: 52
Parker AC30V Series Manual preview
AC30V Series
Бренд: Parker Страницы: 337
YOKOGAWA UP150 Instruction Manual preview
UP150
Бренд: YOKOGAWA Страницы: 33
Samson 46-7 Mounting And Operating Instructions preview
46-7
Бренд: Samson Страницы: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Бренд: Hansen Страницы: 12
Watt Stopper MRDS10 Installation Instructions preview
MRDS10
Бренд: Watt Stopper Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды