Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 941 | Manualshive

Страница: 941 / 1153

background image

Preface

MPC5565 Microcontroller Reference Manual, Rev. 1.0

21-4

Freescale Semiconductor

21.1.4

Modes of Operation

The device supports four FlexCAN functional modes: normal, freeze, listen-only and loop-back. One low
power mode, module disabled, is supported.

21.1.4.1

Normal Mode

In normal mode, the module operates receiving and/or transmitting message frames, errors are handled
normally and all the CAN protocol functions are enabled. In this device, there is no distinction between
user and supervisor modes.

21.1.4.2

Freeze Mode

Freeze mode is entered when the FRZ bit in the module configuration register (CAN

x

_MCR) is asserted

while the HALT bit in the CAN

x

_MCR is set or debug mode is requested by the NPC. In freeze mode no

transmission or reception of frames is done, and synchronization with the CAN bus is lost. Refer to

Section 21.4.6.1, “Freeze Mode

,” for more information.

21.1.4.3

Listen-Only Mode

The module enters this mode when the LOM bit in the CAN

x

_CR is asserted. In this mode, FlexCAN

operates in a CAN error passive mode, freezing all error counters and receiving messages without sending
acknowledgments.

21.1.4.4

Loop-Back Mode

The module enters this mode when the LPB bit in the CAN

x

_CR is asserted. In this mode, FlexCAN

performs an internal loop back that can be used for self test operation. The bit stream output of the
transmitter is internally fed back to the receiver input. The CAN receive input pin (CNRX

x

) is ignored and

the transmit output (CNTX

x

) goes to the recessive state (logic 1). FlexCAN behaves as it normally does

when transmitting, and treats its own transmitted message as a message received from a remote node. In
this mode, FlexCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field to
ensure proper reception of its own message. Both transmit and receive interrupts are generated.

21.1.4.5

Module Disabled Mode

This low power mode is entered when the MDIS bit in the CAN_MCR is asserted. When disabled, the
module shuts down the clocks to the CAN protocol interface and message buffer management submodules.
Exit from this mode is done by negating the CAN_MCR[MDIS] bit. Refer to

Section 21.4.6.2, “Module

,” for more information.

21.2

External Signal Description

21.2.1

Overview

The FlexCAN2 module has two I/O signals connected to the external MCU pins. These signals are
summarized in

and described in more detail in the next sub-sections.

«
...
939
940
941
942
943
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: H3C Страницы: 27

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 10

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: Daruifuno Страницы: 24

Бренд: Computer Automation Technology Страницы: 55

Бренд: Auber Страницы: 3

Бренд: Greenheck Страницы: 4

Бренд: YOKOGAWA Страницы: 33

Lift Inverter L1000V

Бренд: YASKAWA Страницы: 282

Бренд: Instrutech Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды